Onkyo TX-NR6100 7.2-Channel THX Certified AV Receiver Instruction Manual - Eng - Page 136

Multi Zone Sound Check, ARC Setup, AccuEQ Room Calibration, SETUP MIC

Get Onkyo TX-NR6100 7.2-Channel THX Certified AV Receiver PDF manuals and user guides View all Onkyo TX-NR6100 7.2-Channel THX Certified AV Receiver manuals
Add to My Manuals
Save this manual to your list of manuals

Page 136 highlights

press ENTER. „„2. Multi Zone Sound Check Output test tones to ZONE 2 to enjoy audio in a separate room (ZONE 2) in addition to the main room. „„3. ARC Setup If you have connected a TV that supports ARC, select "Yes" and press ENTER. „„4. AccuEQ Room Calibration Place the supplied speaker setup microphone in the listening position, measure the test tones emitted by the speakers, then the unit automatically sets the optimum volume level for each speaker, the crossover frequencies, and the distance from the listening position. This also automatically adjusts the equalizers for the speakers, and enables correction of distortion caused by the acoustic environment of the room. • It takes between 3 and 12 minutes for calibration to be completed. Each speaker outputs the test tone at high volume during measurement, so be careful of your surroundings. Also, keep the room as quiet as possible during measurement. • If you connect a subwoofer, check the power and volume of the subwoofer. Set the subwoofer volume to more than half. • If the power of this unit suddenly turns off, the wires in the speaker cables have touched the rear panel or other wires, and the protection circuit is working. Twist the wires again securely, and make sure they do not stick out of the speaker terminals when connecting. • When using THX certified speakers, THX recommends that the crossover frequency is set to "80Hz(THX)". Also, THX recommends that each speaker setting is manually adjusted according to the specific characteristics of each room. Setup 1. Place the supplied speaker setup microphone at the listening position, and connect it to the SETUP MIC jack on the main unit. SETUP MIC When placing the speaker setup microphone on a tripod, refer to the illustration. 2. Confirm a test tone is output from the subwoofer and press ENTER. 3. Press ENTER to output test tones from each speaker, and the connected speakers and the noise in the surrounding environment are automatically measured. 4. The measurement results in step 3 are displayed. If there is no problem in the detection result of the speaker, select "Next" and press ENTER to output the test tone again to automatically set the settings such as volume level, crossover frequency, etc., to their optimum. (The test tone is automatically output when 10 seconds has elapsed without any operation.) 5. When the measurement is completed, the measurement results are displayed. You can check each setting using the cursors / . Select "Save" and press ENTER to save the settings. 6. Disconnect the speaker setup microphone. 136

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
136
Setup
press ENTER.
±
2. Multi Zone Sound Check
Output test tones to ZONE 2 to enjoy audio in a separate room (ZONE 2) in
addition to the main room.
±
3. ARC Setup
If you have connected a TV that supports ARC, select "Yes" and press ENTER.
±
4. AccuEQ Room Calibration
Place the supplied speaker setup microphone in the listening position, measure
the test tones emitted by the speakers, then the unit automatically sets the
optimum volume level for each speaker, the crossover frequencies, and
the distance from the listening position. This also automatically adjusts the
equalizers for the speakers, and enables correction of distortion caused by the
acoustic environment of the room.
•
It takes between 3 and 12 minutes for calibration to be completed. Each
speaker outputs the test tone at high volume during measurement, so be
careful of your surroundings. Also, keep the room as quiet as possible during
measurement.
•
If you connect a subwoofer, check the power and volume of the subwoofer.
Set the subwoofer volume to more than half.
•
If the power of this unit suddenly turns off, the wires in the speaker cables
have touched the rear panel or other wires, and the protection circuit is
working. Twist the wires again securely, and make sure they do not stick out
of the speaker terminals when connecting.
• When using THX certified speakers, THX recommends that the crossover
frequency is set to "80Hz(THX)". Also, THX recommends that each speaker
setting is manually adjusted according to the specific characteristics of each
room.
1. Place the supplied speaker setup microphone at the listening position, and
connect it to the SETUP MIC jack on the main unit.
SETUP MIC
When placing the speaker setup microphone on a tripod, refer to the
illustration.
2.
Confirm a test tone is output from the subwoofer and press ENTER.
3. Press ENTER to output test tones from each speaker, and the connected
speakers and the noise in the surrounding environment are automatically
measured.
4. The measurement results in step 3 are displayed. If there is no problem in
the detection result of the speaker, select "Next" and press ENTER to output
the test tone again to automatically set the settings such as volume level,
crossover frequency, etc., to their optimum. (The test tone is automatically
output when 10 seconds has elapsed without any operation.)
5. When the measurement is completed, the measurement results are
displayed. You can check each setting using the cursors
/
. Select "Save"
and press ENTER to save the settings.
6.
Disconnect the speaker setup microphone.