Onkyo TX-NR777 Owners Manual -Basic - Page 14

Step2: Connect the Speakers

Get Onkyo TX-NR777 PDF manuals and user guides View all Onkyo TX-NR777 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

> Before Start > Part Names > Install > Initial Setup > Playback Step2: Connect the Speakers 1/2˝ (12 mm) Standard Connections (Pages 8 to 11) Up to two powered subwoofers can be connected. The same signal is output from each of the SUBWOOFER PRE OUT jacks. Setup 0 Settings for the speaker configuration you have connected need to be made in "1. AccuEQ Room Calibration" in Initial Setup (P23). 0 If any of the connected speakers have an impedance of 4 Ω or more to less than 6 Ω, after completing Initial Setup, you need to make some settings in the Setup menu. Press on the remote controller, select "2. Speaker" "Configuration" and set "Speaker Impedance" to "4ohms". b a a Speaker cable, b Subwoofer cable 14 Make sure the exposed wires of the speakers do not stick out of the speaker terminals when connecting. If the exposed wires of the speakers touch the rear panel or the + and - wires touch each other, the protection circuit will be activated.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
14
Step2: Connect the Speakers
Standard Connections (Pages 8 to 11)
Up to two powered subwoofers can be connected. The
same signal is output from each of the SUBWOOFER PRE
OUT jacks.
Make sure the exposed wires of the speakers
do not stick out of the speaker terminals when
connecting. If the exposed wires of the
speakers touch the rear panel or the + and –
wires touch each other, the protection circuit
will be activated.
> Before Start
> Part Names
> Install
> Initial Setup
> Playback
a
b
1/2˝
(12 mm)
a
Speaker cable,
b
Subwoofer cable
Setup
0
Settings for the speaker configuration you have
connected need to be made in "1. AccuEQ Room
Calibration" in Initial Setup (P23).
0
If any of the connected speakers have an
impedance of 4 Ω or more to less than 6 Ω, after
completing Initial Setup, you need to make some
settings in the Setup menu. Press
on the
remote controller, select "2. Speaker" -
"Configuration" and set "Speaker Impedance" to
"4ohms".