Onkyo TX-RZ3100 AV Receiver Basic/Advanced Manual English - Page 27
> Playback, Troubleshooting | Appendix
View all Onkyo TX-RZ3100 AV Receiver manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 27 highlights
> Before start > Hookup > Setup > Playback > Part Names > Advanced Manual Troubleshooting | Appendix separate room or the ZONE Speaker, adjust with VOL+/- on the remote controller. To control on the main unit, press ZONE 2 or ZONE 3 and adjust with the MASTER VOLUME control within 8 seconds. 0 The information for a connected device can be displayed on the TV screen in a separate room. Press the button while the remote controller is in the mode for controlling ZONE 2. 0 Power consumption in standby mode increases when the multi-zone function is being used. To turn off the function Press Í ON/STANDBY while in the mode for controlling ZONE 2 or ZONE 3 on the remote controller. Playing in ZONE 2 or ZONE 3 only If you turn the unit to standby during multi-zone playback, the Z2 or Z3 indicator is dimmed and the playback mode is switched to playback in a separate room only. Setting ZONE 2/ZONE 3 to on while this unit is in standby will also switch the playback mode to the same setting. WHOLE HOUSE MODE If you press WHOLE HOUSE MODE while playback is being performed in the main room, the WHOLE HOUSE MODE is turned on, "Z2" and "Z3" on the display light at the same time and the playback sources of all the rooms are switched to the same source at once. 0 The sources that can be played in ZONE 2 can be played in all rooms. 0 This function cannot be used if headphones are connected or audio is output from the speakers of the TV. Settings Settings are required in Initial Setup, "4. Multi Zone Setup" (P22) to use the multi-zone feature. When checking the setting content, refer to the following, press on the remote controller, and check in the Setup menu that is displayed. - When you have connected a TV in the separate room with an HDMI cable, have you selected "Use" in "1. Input/ Output Assign" - "TV Out/OSD" - "Zone2 HDMI"? - When you are playing the audio from an AV component with an HDMI cable in the separate room, have you selected "Use" in "1. Input/Output Assign" - "TV Out/ OSD" - "Zone2 HDMI"? - When you have connected speakers in a separate room with speaker cable, have you selected "Zone 2" or "Zone 2/Zone 3" in "2. Speaker" - "Configuration" - "Zone Speaker"? - When you have connected a power amplifier in a separate room with an analog audio cable and you want to control the volume with this unit, have you selected "Variable" in "6. Multi Zone" - "Zone 2" or "Zone 3" - "Output Level"? Others To adjust the sound quality It is possible to enhance or moderate the bass and treble range of all channels except the subwoofer channel. Press TONE on the main unit several times to select the desired setting from "Bass" and "Treble", and turn the TONE dial to adjust. 0 This cannot be set if the listening mode is Pure Audio, Direct or THX. 0 You can also adjust the sound quality of a power amplifier connected in a separate room. After pressing either ZONE 2 or ZONE 3 on the main unit, within 8 seconds press TONE and turn the TONE dial to adjust. Quick Menu By pressing Q on the remote controller during play, you can adjust frequently used settings, such as the sound quality, using on-screen menus. Select the item with the cursors of the remote controller and press ENTER to confirm your selection. To return to the previous screen, press . Quick Menu Tone Level AccuEQ Other Bass Treble BD/DVD 0 You can adjust the sound quality with "Tone". "Other" includes settings such as "A/V Sync" that allows you to adjust the audio delay when the video is behind the audio, "Music Optimizer" that provides better sound quality for compressed audio, and "HDMI Out" which allows you to select the HDMI OUT terminal to output from "MAIN", "SUB", and "MAIN+SUB". 27