Onkyo TX-SR707 Owner Manual - Page 105

Using Zone 2, Controlling Zone 2 from the AV receiver, Controlling Zone 2 with the Remote, Controller

Page 105 highlights

Zone 2-Continued Using Zone 2 This section explains how to turn Zone 2 on and off, how to select an input source for Zone 2, and how to adjust the volume for Zone 2. Controlling Zone 2 from the AV receiver ZONE 2 OFF Controlling Zone 2 with the Remote Controller STANDBY ON ZONE2 INPUT SELECTOR ZONE 2 indicator Input selector buttons 1 To turn on Zone 2 and select an input source, press the [ZONE 2] button followed by an input selector button within 8 seconds. Zone 2 turns on, the ZONE 2 indicator lights up. Tip : The 12V TRIGGER OUT ZONE 2 goes high (+12 V). To select AM or FM press the [TUNER] input selector and the [ZONE 2] button repeatedly. You can also select SIRIUS (North American models). To select the same source as that of the main room, press the [ZONE 2] button twice. "Zone 2 Selector: Source" appears on the display. 2 To turn off Zone 2, press the [ZONE 2] button. The ZONE 2 indicator flashes. Press the [OFF] button. The zone is turned off, and the ZONE 2 indicator goes off. Note: When Zone 2 is turned off, the output from the 12V TRIGGER OUT ZONE 2 goes low (0 volts). Note: To control Zone 2, you must press the remote controller's [ZONE2] button first. The ZONE2 button turns red while Zone 2 is on. 1 Press the [ZONE2] button, then point the remote controller at the AV receiver and press the [ON] button. Tip : The 12V TRIGGER OUT ZONE 2 goes high (+12 V). 2 To select an input source for Zone 2, press the [ZONE2] button, followed by an INPUT SELECTOR button. To select AM or FM press the [TUNER] INPUT SELECTOR and the [ZONE2] button repeatedly. You can also select SIRIUS (North American models). 3 To turn off Zone 2, press the [ZONE2] button, followed by the [STANDBY] button. 105

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128

105
Zone 2
—Continued
This section explains how to turn Zone 2 on and off, how
to select an input source for Zone 2, and how to adjust
the volume for Zone 2.
Controlling Zone 2 from the AV receiver
Note:
When Zone 2 is turned off, the output from the 12V
TRIGGER OUT ZONE 2 goes low (0 volts).
Controlling Zone 2 with the Remote
Controller
Note:
To control Zone 2, you must press the remote control-
ler’s [ZONE2] button first.
The ZONE2 button turns red while Zone 2 is on.
Using Zone 2
1
To turn on Zone 2 and select an
input source, press the [ZONE 2]
button followed by an input
selector button within 8 seconds.
Zone 2 turns on, the ZONE 2 indicator
lights up.
Tip :
The 12V TRIGGER OUT ZONE 2
goes high (+12 V).
To select AM or FM press the
[TUNER] input selector and the
[ZONE 2] button repeatedly. You can
also select SIRIUS
(North American
models)
.
To select the same source as that of the
main room, press the [ZONE 2] button
twice. “Zone 2 Selector: Source”
appears on the display.
2
To turn off Zone 2, press the
[ZONE 2] button.
The ZONE 2 indicator flashes.
Press the [OFF] button.
The zone is turned off, and the ZONE 2
indicator goes off.
OFF
Input selector buttons
ZONE 2
ZONE 2 indicator
1
Press the [ZONE2] button, then
point the remote controller at the
AV receiver and press the [ON]
button.
Tip :
The 12V TRIGGER OUT ZONE 2
goes high (+12 V).
2
To select an input source for
Zone 2, press the [ZONE2]
button, followed by an INPUT
SELECTOR button.
To select AM or FM press the
[TUNER]
INPUT SELECTOR
and the
[ZONE2] button repeatedly. You can
also select SIRIUS
(North American
models)
.
3
To turn off Zone 2, press the
[ZONE2] button, followed by the
[STANDBY] button.
INPUT
SELECTOR
ON
ZONE2
STANDBY