Optoma W515 User manual - Page 19

Powering off

Get Optoma W515 PDF manuals and user guides View all Optoma W515 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

USING THE PROJECTOR Powering off 1. Turn off the projector by pressing the " " either on the projector keypad or the remote control. 2. The following message will be displayed: Power Off? Press Power again 3. Press the " " again to confirm otherwise the message will disappear after 15 seconds. When you press the " " button for the second time the projector will shut down. 4. The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/ Standby LED will flash green. When the On/Standby LED turns solid red the projector has entered standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has finished and the projector has entered standby mode. When the projector is in standby mode simply press the " " button again to turn on the projector. 5. Disconnect the power lead from the electrical outlet and the projector. Note: (*) optional accessory vary depending on model, specification and region. It is not recommended that the projector is tuned on immediately following a power off procedure. English 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
English
19
USING THE PROJECTOR
Powering off
Turn off the projector by pressing the
1.
"
" either on the projector keypad or the remote control.
The following message will be displayed:
2.
Power Off?
Press Power again
Press the
3.
"
" again to confirm otherwise the message will disappear after 15 seconds. When you
press the "
" button for the second time the projector will shut down.
The cooling fans will continue to operate for about 10 seconds for the cooling cycle and the On/
4.
Standby LED will flash green. When the On/Standby LED turns solid red the projector has entered
standby mode. If you wish to turn the projector back on, you must wait until the cooling cycle has
finished and the projector has entered standby mode. When the projector is in standby mode simply
press the "
" button again to turn on the projector.
Disconnect the power lead from the electrical outlet and the projector.
5.
(*) optional accessory vary depending on model, specification and region.
Note°
It is not recommended that the projector is tuned on immediately following a power off procedure.