Optoma ZK430ST Manual - Page 50

Control reset menu, RS232 by Telnet Function, Quick Start-Guide for RS232 by Telnet, Search

Get Optoma ZK430ST PDF manuals and user guides View all Optoma ZK430ST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

USING THE PROJECTOR RS232 by Telnet Function RS232 by Telnet Function As an alternative method of control, this projector has RS232 command control by TELNET for LAN / RJ45 interface. Quick Start-Guide for "RS232 by Telnet" ‡ Check and get the IP address on OSD of the projector. ‡ Make sure that the PC / laptop can access the web-page of the projector. ‡ Make sure that "Windows Firewall" setting is set to disabled in case of "TELNET" function filtering out by PC / laptop. 1. Click on Search and then enter "cmd" as a search word. Press the "Enter" key. 2. Open the Command Prompt app. 3. Input the command format as follows: ± telnet ttt.xxx.yyy.zzz 23 ("Enter" key pressed) ± (ttt.xxx.yyy.zzz: IP-Address of the projector) 4. If Telnet-Connection ready, and user can have RS232 command input, then press the "Enter" key and Telnet connection should be ready for RS232 command control. Specification for "RS232 by TELNET": 1. Telnet: TCP. 2. Telnet port: 23 (for further details, please contact the Optoma service team). 3. Telnet utility: Windows "TELNET.exe" (console mode). 4. To end the Telnet session, just close the Command Prompt app window. 5. Windows Telnet utility directly after TELNET connection ready. ± Limitation 1 for Telnet-Control: There cannot be more than 50 bytes for successive network payload for Telnet-Control application. ± Limitation 2 for Telnet-Control: There cannot be more than 26 bytes for successive RS232 command for Telnet-Control. ± Limitation 3 for Telnet-Control: Minimum delay for next command must be more than 200 (ms). Control reset menu Return the factory default settings for control settings. 50 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
English
50
USING THE PROJECTOR
RS232 by Telnet Function
As an alternative method of control, this projector has RS232 command control by TELNET for LAN / RJ45
interface.
Quick Start-Guide for “RS232 by Telnet”
±
Check and get the IP address on OSD of the projector.
±
Make sure that the PC / laptop can access the web-page of the projector.
±
Make sure that “Windows Firewall” setting is set to disabled in case of “TELNET” function filtering out
by PC / laptop.
1.
Click on
Search
and then enter “cmd” as a search word. Press the “Enter” key.
2.
Open the Command Prompt app.
3.
Input the command format as follows:
²
telnet ttt.xxx.yyy.zzz 23 (“Enter” key pressed)
²
(ttt.xxx.yyy.zzz: IP-Address of the projector)
4.
If Telnet-Connection ready, and user can have RS232 command input, then press the “Enter” key and
Telnet connection should be ready for RS232 command control.
Specification for “RS232 by TELNET”
:
1.
Telnet: TCP.
2.
Telnet port: 23 (for further details, please contact the Optoma service team).
3.
Telnet utility: Windows “TELNET.exe” (console mode).
4.
To end the Telnet session, just close the Command Prompt app window.
5.
Windows Telnet utility directly after TELNET connection ready.
²
Limitation 1 for Telnet-Control: There cannot be more than 50 bytes for successive network
payload for Telnet-Control application.
²
Limitation 2 for Telnet-Control: There cannot be more than 26 bytes for successive RS232
command for Telnet-Control.
²
Limitation 3 for Telnet-Control: Minimum delay for next command must be more than 200 (ms).
Control reset menu
Return the factory default settings for control settings.
RS232 by Telnet Function