Panasonic MCV414 MCV414 User Guide - Page 32

REPLACING BELT, Lift Agitator Up, Felt Packing, Rear Belt, Cover, Install New Belt, Motor Shaft

Get Panasonic MCV414 - COMMERCIAL VACUUM PDF manuals and user guides View all Panasonic MCV414 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Replacing Belt ➢ Replace belt whenever a burning rubber smell caused by excessive slippage + occurs. Rear Belt + Cover Couvre- courroie arrière Cubierta de la correa trasera Felt Packing Cale en feutre Empaquetadura de filtro Lift Agitator Up Soulever l'agitateur Unidad del agitador ➢ Remove lower plate. ➢ Lift rear belt cover and remove felt packing. ➢ Remove agitator by carefully lifting out. ➢ Remove worn or broken belt. ➢ Clean agitator. Motor Shaft Arbre d'entraînement du moteur Eje del motor Install New Belt Poser la nouvelle courroie Instalación de la correa ➢ Loop new belt (Type UB8 only) around motor shaft and agitator pulley; see illustration for correct belt routing. ➢ Reinstall agitator back into nozzle housing grooves. ➢ Close rear belt cover and reinstall felt packing. + + ➢ After reinstalling the agitator, turn it by hand to make sure that belt is not twisted or pinched and that all rotating parts turn freely. ➢ Reinstall lower plate. Groove Ouverture Ranura End Cap Bouchon Tapa del extremo - 32 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Replacing Belt
+
+
Lift Agitator Up
Soulever l’agitateur
Unidad del agitador
Felt Packing
Cale en feutre
Empaquetadura
de filtro
Rear Belt
Cover
Couvre-
courroie
arrière
Cubierta
de la correa
trasera
Install New Belt
Poser la nouvelle courroie
Instalación de la correa
Motor Shaft
Arbre
d’entraînement
du moteur
Eje del motor
➢
Replace belt whenever a burning rubber
smell caused by excessive slippage
occurs.
➢
Remove lower plate.
➢
Lift rear belt cover and remove felt
packing.
➢
Remove agitator by carefully lifting out.
➢
Remove worn or broken belt.
➢
Clean agitator.
➢
Loop new belt (Type UB8 only) around
motor shaft and agitator pulley; see
illustration for correct belt routing.
➢
Reinstall agitator back into nozzle
housing grooves.
➢
Close rear belt cover and reinstall felt
packing.
➢
After reinstalling the agitator, turn it by
hand to make sure that belt is not
twisted or pinched and that all rotating
parts turn freely.
➢
Reinstall lower plate.
+
+
Groove
Ouverture
Ranura
End Cap
Bouchon
Tapa del extremo
- 32 -