Panasonic TH-55LFE8U Professional Display for Simple Entry-Level Digital Signage - Page 18

Page 18 highlights

PC IN terminal connection (Female) Shared with DVI-D IN. (Male) Connect a cable which matches the audio output terminal on the computer. (not supplied) Mini D-sub 15p (not supplied) Conversion adapter (if necessary) (not supplied) Stereo mini plug (M3) cable (not supplied) COMPUTER The type of computer signal that can be connected Ɣ With regard to the typical PC input signals that are described in "Preset Signals" (see page 75), adjustment values such as for the standard picture positions and sizes have already been stored in this unit. You can add up to eight PC input signal types that are not included in the list. Ɣ Computer signals which can be input are those with a horizontal scanning frequency of 30 to 110 kHz and vertical scanning frequency of 48 to 120 Hz. Ɣ The display resolution is a maximum of 1 440 × 1 080 dots when the aspect mode is set to [4:3], and 1 920 × 1 080 dots when the aspect mode is set to [16:9]. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. Ɣ In [ENGLISH(US)] OSD language, [16:9] is displayed as [FULL]. Note Ɣ The PC IN terminal is DDC2B-compatible. If the computer being connected is not DDC2B-compatible, you will need to make setting changes to the computer at the time of connection. Ɣ Some PC models cannot be connected to the set. Ɣ There is no need to use an adapter for computers with DOS/V compatible Mini D-sub 15P terminal. Ɣ The computer shown in the illustration is for example purposes only. Ɣ Additional computer, cables and conversion adapter 18 English shown are not supplied with this set. Ɣ Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. Ɣ Component Input is possible with the pin 1, 2, 3 of the Mini D-sub 15P Connector. Ɣ Change the [Component/RGB-in select] setting in the [Signal] menu to [Component] (when Component signal connection) or [RGB] (when RGB signal connection). (see page 48) Ɣ Do not set the horizontal and vertical scanning frequencies of PC signals to those exceeding or falling below the specified frequency ranges. Pin assignments and signal names for PC Input Terminal (Mini D-sub 15P) 54 321 10 9 8 7 6 15 14 13 12 11 Pin No. Signal Name R (PR/CR) G (Y) B (PB/CB) NC (not connected) GND (Ground) GND (Ground) GND (Ground) GND (Ground) +5 V DC GND (Ground) NC (not connected) SDA HD/SYNC VD SCL

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
English
18
PC IN terminal connection
Connect a cable
which matches
the audio output
terminal on the
computer.
(not supplied)
(Male)
(Female)
Shared with DVI-D IN.
Mini D-sub 15p (not supplied)
Conversion adapter (if necessary) (not supplied)
Stereo mini plug (M3) cable (not supplied)
COMPUTER
The type of computer signal that can be connected
Ɣ
With regard to the typical PC input signals that
are described in “Preset Signals” (see page 75),
adjustment values such as for the standard picture
positions and sizes have already been stored in this
unit. You can add up to eight PC input signal types that
are not included in the list.
Ɣ
Computer signals which can be input are those with
a horizontal scanning frequency of 30 to 110 kHz and
vertical scanning frequency of 48 to 120 Hz.
Ɣ
The display resolution is a maximum of 1 440 × 1 080
dots when the aspect mode is set to [4:3], and 1 920
× 1 080 dots when the aspect mode is set to [16:9].
If the display resolution exceeds these maximums, it
may not be possible to show fine detail with sufficient
clarity.
Ɣ
In [ENGLISH(US)] OSD language, [16:9] is displayed
as [FULL].
Note
Ɣ
The PC IN terminal is DDC2B-compatible. If the
computer being connected is not DDC2B-compatible,
you will need to make setting changes to the computer
at the time of connection.
Ɣ
Some PC models cannot be connected to the set.
Ɣ
There is no need to use an adapter for computers with
DOS/V compatible Mini D-sub 15P terminal.
Ɣ
The computer shown in the illustration is for example
purposes only.
Ɣ
Additional computer, cables and conversion adapter
shown are not supplied with this set.
Ɣ
Do not set the horizontal and vertical scanning
frequencies for PC signals which are above or below
the specified frequency range.
Ɣ
Component Input is possible with the pin 1, 2, 3 of the
Mini D-sub 15P Connector.
Ɣ
Change the [Component/RGB-in select] setting in
the [Signal] menu to [Component] (when Component
signal connection) or [RGB] (when RGB signal
connection). (see page 48)
Ɣ
Do not set the horizontal and vertical scanning
frequencies of PC signals to those exceeding or
falling below the specified frequency ranges.
Pin assignments and signal names for PC Input
Terminal (Mini D-sub 15P)
1
6
7
8
3
9
4
5
10
15
14
13
12
11
2
Pin No.
Signal Name
R (P
R
/C
R
)
G (Y)
B (P
B
/C
B
)
NC (not connected)
GND (Ground)
GND (Ground)
GND (Ground)
GND (Ground)
+5 V DC
GND (Ground)
NC (not connected)
SDA
HD/SYNC
VD
SCL