Panasonic TH-55LFE8U Professional Display for Simple Entry-Level Digital Signage - Page 62

Serial ID function, LAN control protocol, Information timing, Select the item with, Select the set

Get Panasonic TH-55LFE8U Professional Display for Simple Entry-Level Digital Signage PDF manuals and user guides View all Panasonic TH-55LFE8U Professional Display for Simple Entry-Level Digital Signage manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Serial ID function Set to control external control with the PC connected to SERIAL terminal according to the Display's ID number (Panel ID). [Off]: Disables external control by the ID. [On]: Enables the external control by the ID. LAN control protocol Select the LAN control protocol. [Protocol 1]: Control with the Panasonic Display sequence. [Protocol 2]: Control with the sequence that compatible with Panasonic Projector. Note Ɣ For PJLink and WEB browser control, the operation is possible regardless of the setting. Ɣ When performing the command control with TCP/IP, select [Protocol 1]. Ɣ When operating the Early warning software or Multi Monitoring & Control Software, select [Protocol 2]. Information timing Set up the informing manner for no signal. During RS-232C controls: Warning or error message sent on the display automatically. During LAN controls: Acquire the warning or error message from the display. 1 Select the item with . Select the set point with . Information timing No signal warning No signal warning timing On 5min No signal error No signal error timing On 10min [No signal warning] When set to [On], the display sends out the no signal warning. [No signal warning timing] Set up the detecting time for no signal warning. (Range: 01 - 60, Interval: 1 minute) [No signal error] When set to [On], the display sends out the no signal error. [No signal error timing] Set up the detecting time for no signal error. (Range: 01 - 90, Interval: 1 minute) Ɣ The warning of [No signal warning] and the error of [No signal error] are not sent when the no signal state is detected through any of the following functions: [No signal power off], [HDMI1 power management], [HDMI2 power management], [DVI-D power management], [PC power management] (see page 51) Ɣ If there is no signal when [PC IN] is input, [PC power management] is activated first and the Display enters the standby mode. Setting Example: [No signal warning timing]: 5 minutes [No signal error timing]: 10 minutes [PC power management]: [On] (60 seconds) Note Ɣ The [No signal error timing] cannot be set shorter than [No signal warning timing]. 62 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
English
62
Serial ID function
Set to control external control with the PC connected to
SERIAL terminal according to
the Display’s ID number
(Panel ID).
[Off]:
Disables external control by the ID.
[On]:
Enables the external control by the ID.
LAN control protocol
Select the LAN control protocol.
[Protocol 1]:
Control with the Panasonic Display
sequence.
[Protocol 2]:
Control with the sequence that
compatible with Panasonic Projector.
Note
Ɣ
For PJLink and WEB browser control, the operation is
possible regardless of the setting.
Ɣ
When performing the command control with TCP/IP,
select [Protocol 1].
Ɣ
When operating the Early warning software or Multi
Monitoring & Control Software, select [Protocol 2].
Information timing
Set up the informing manner for no signal.
During RS-232C controls:
Warning or error message sent on the display
automatically.
During LAN controls:
Acquire the warning or error message from the
display.
1
Select the item with
.
Select the set point with
.
Information timing
No signal warning
No signal warning timing
No signal error
No signal error timing
On
5min
On
10min
[No signal warning]
When set to [On], the display sends out the no signal
warning.
[No signal warning timing]
Set up the detecting time for no signal warning.
(Range: 01 - 60, Interval: 1 minute)
[No signal error]
When set to [On], the display sends out the no signal
error.
[No signal error timing]
Set up the detecting time for no signal error.
(Range: 01 - 90, Interval: 1 minute)
Ɣ
The warning of [No signal warning] and the error of
[No signal error] are not sent when the no signal state
is detected through any of the following functions:
[No signal power off], [HDMI1 power management],
[HDMI2 power management], [DVI-D power
management], [PC power management] (see page
51)
Ɣ
If there is no signal when [PC IN] is input, [PC power
management] is activated first and the Display enters
the standby mode.
Setting Example:
[No signal warning timing]: 5 minutes
[No signal error timing]: 10 minutes
[PC power management]: [On] (60 seconds)
Note
Ɣ
The [No signal error timing] cannot be set shorter
than [No signal warning timing].