Panasonic WVCW474F WVCW474F User Guide - Page 4

SETUP 1. CAMERA SETUP MENU This camera utilizes an on-screen user setup menu. • Opening the Setup Menu Press and hold down I(S) for 2 seconds or more. The CAM SET UP menu appears on the monitor as shown at right. Check the current settings on the menu. ** CAM SET UP ** ↵↵ CAMERA ID OFF ALC ALC SHUTTER --- AGC ON(DNR-H) SENS UP OFF SYNC INT ↵ WHITE BAL ATW1 MOTION DET OFF DIP SW END SET UP DISABLE Refer to the following sections for a detailed description of menu items. If you decide not to make any changes after checking the current settings, move the cursor to END in the bottom line, and press I(S) to close the setup menu. Note: If no button is pressed for 6 minutes while a setup menu is being displayed on the monitor screen, it is automatically closed and the mode returns to the normal camera picture. 2. SETUP OPERATION This camera utilizes an on-screen user setup menu (CAM SET UP). To set items on the CAM SET UP menu, use the following buttons on the side panel. Left Button (I) (L): Moves the cursor to the left. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button is pressed. Right Button (I) (R): Moves the cursor to the right. Use this button to select or adjust the parameters of the selected item. The parameter changes each time this button is pressed. Up Button (I) (U): Moves the cursor upwards. Use this button to select an item or adjust the parameters. Down Button (I) (D): Moves the cursor downwards. Use this button to select an item or adjust the parameters. Set Button (I) (S): Executes selections and displays a submenu for an item with the mark. ↵ • To reset the parameter to the factory default setting, move the cursor to the parameter to be reset and press I(L) and I(R) simultaneously. • To return to the previous menu or page, move the cursor to RET and press I(S). • To close the setup menu, move the cursor to END and press I(S). • All Reset Operation All Reset allows you to reset all setup menu items to the factory default settings if you are unsure about the correct settings. Proceed as follows: (1) Make sure that the CAM SET UP menu is not displayed (a camera picture is displayed). (2) While pressing both I(L) and I(R), press I(S) for a few seconds. The message ALL RESET momentarily appears on the monitor screen. This resets all adjustments and parameters to the factory default settings. • Editing the CAM SET UP Menu Important Notice: When SET UP DISABLE appears in the bottom line of the CAM SET UP menu, you cannot change the currently active settings. This is to prevent accidental changing of the settings. To edit the CAM SET UP menu (change settings), press I(U) and I(D) or I(L) and I(R) to move the cursor to SET UP DISABLE in the bottom line. Press I(S). SETUP DISABLE changes to SETUP ENABLE. Move the cursor to DIP SW. Press I(S). DIP SW changes to MENU. Then move the cursor to the item(s) you want to change. ** CAM SET UP ** ↵↵ CAMERA ID OFF ALC ALC SHUTTER --- AGC ON(DNR-H) SENS UP OFF SYNC INT ↵ WHITE BAL ATW1 MOTION DET OFF DIP SW END SET UP DISABLE ** CAM SET UP ** ↵↵ CAMERA ID OFF ALC ALC SHUTTER --- AGC ON(DNR-H) SENS UP OFF SYNC INT ↵ WHITE BAL ATW1 MOTION DET OFF MENU END SET UP ENABLE Notes: • When DIP SW is selected for CAM SET UP menu, five modes can be set with the DIP switches. • To operate the camera functions with the system controller, select MENU in the CAM SET UP menu. Important Notice: When the setup menu is closed after changing the parameters in the menu, the new values are stored in the EEPROM (Electrically Erasable and Programmable Read-Only Memory). These values remain valid until new values are stored, even if the power of the camera is off.