Philips FW930 User manual - Page 21

CD RECORDER English MANUAL RECORDING 3 Play the source first to set the optimal Note: ™ For CDR(W), CDR(W) changes to CD on Preparing for manual recording recording level on the CD recorder. - With "AUTO TRACK ON", the display. 1 Press SOURCE repeatedly to select DIGITAL, OPTICAL or ANALOG mode. • When Auto Track is ON (default setting), track numbers will automatically be increased during recording. 4 Rotate EASY JOG until all the blue segments are alight on the record/play Level Bar, but the red segments do not light continuously during the loudest passages. recorder will stop and go to REC STANDBY for 1 minute and then goes to stop mode automatically. Recordings from DAT, DCC or recordings made analogously will stop after 20 seconds Notes: - Finalizing will take at least 2-4 minutes. - During finalization, the CD recorder accepts no operating commands. ™ To switch off the Auto Track function you have to enter Menu mode. If you wish to increase track numbers manually, press TRACK INCREMENT on the remote control. For further instructions see Menu mode. ON (AUTO) .... The track increments ™ "-XX DB" appears on the display. 5 Stop the source. Start manual recording 1 To start recording, press RECORD on the CD Recorder and immediately start playback of the selected source (from silence. With "AUTO TRACK OFF", the auto stop mode is disabled. FINALIZING CDR & CDRW DISCS Finalizing is a simple procedure, necessary to: - be able to play recordings on a CD UNFINALIZING CDRW DISCS For CDRW discs only If you want to make more recordings (or erasures of tracks) on a finalized disc you must unfinalize it first. The Table of Contents (TOC) will be removed. are automatically taken over from the digital source material or after 2.7 seconds silence during analog recording. ON (MANUAL)...Track numbers can be incremented manually by pressing Stop-mode). ™ The track number and recording time appear on the display. • To record a 3-second silence at the start of a track, press PAUSE ; on the CD Recorder before starting the selected source. • To check the elapsed recording time, press DISPLAY on the CD recorder (This PLAYER, - avoid further unwanted recordings on a disc, - avoid erasure of tracks on a CDRW. Auto finalizing Auto finalizing is possible when using the MAKE CD recording function. To unfinalize 1 Press REC TYPE or ERASE in stop mode. ™ "UNFINALIZE" and "PRESS ENTER" appear on the display. 2 Press ENTER to confirm unfinalize. ™ The disc will now be unfinalized and can be recorded on again. TRACK INCR(ement) on can also be done during the recording). Manual finalizing Notes: the remote control. 2 To stop recording, press STOP Ç on 1 Press FINALIZE in stop mode. - Unfinalizing will take approximately 2 (Minimum track length the CD recorder. ™ "FINALIZE" and "PRESS minutes. is 4 sec.) (This can also ™ "WAIT" appears on the display. RECORD" appear on the display. - When unfinalizing a CDRW disc with be done in Auto mode). • Track numbers cannot be changed after recording. 2 Press REC TYPE three times to enter the Manual Record standby mode. ™ The MANUAL flag starts to flash and • If STOP Ç was pressed within 3 seconds after pressing RECORD, no recording will take place. • To interrupt recording, press PAUSE ; on the CD recorder. 2 Press RECORD. ™ "XX XX FINAL" and the approximate finalization time appear on the display. • The display counts down through the finalization. text on it available, this text will be transferred to the CD recorder memory. It may occur that the text memory is full. The message "MEMORY FULL/ FINALIZE CD" will be displayed. You will now have to erase text, stored the display shows "REC MANUAL". After recording, the display will show ™ On completion, the total number of for other discs, or finalize another disc "UPDATE" for several seconds. tracks and the total time recorded in order to obtain memory space. appear on the display. 21