RCA ANT3038XR Owner/User Manual
RCA ANT3038XR Manual
 |
UPC - 044476071638
View all RCA ANT3038XR manuals
Add to My Manuals
Save this manual to your list of manuals |
RCA ANT3038XR manual content summary:
- RCA ANT3038XR | Owner/User Manual - Page 1
English ANT3038XR Outdoor Antenna User's Guide Para obtener instrucciones en español, consulte la página 9. Assembling the ANT3038XR BEFORE YOU START!!! Please read the IMPORTANT SAFETY INFORMATION sheet included in this package. Step 1: Unpack Remove all three sections of the antenna and the - RCA ANT3038XR | Owner/User Manual - Page 2
reflector booms should be parallel to the smaller boom at this point. (See Fig. 1.) Fig. 2A Main Boom Step 3: Unfold the rest of the antenna Unfold all the other elements on the antenna until they lock into place ensuring that they are flat and parallel to each other. (See Fig. 3.) Fig. 3 2 - RCA ANT3038XR | Owner/User Manual - Page 3
holders are also on this same side. This is the top of the antenna. (See figure 5.) Fig. 4 Tap lightly with a rubber mallet on the end of the small boom aligning the holes for the screw. (See figure 4.) Re-install the screw and nut; be sure to tighten securely. Step 5: Connect the phasing - RCA ANT3038XR | Owner/User Manual - Page 4
and screw. Find the rear section. Slide the narrow boom of the rear antenna into the middle (large) section. Tap lightly with a rubber mallet on Nut aligning the holes for the screw. (See figure Fig. 6 6.) Re-install the screw and nut; be sure to tighten securely. Step 7: Connect the phasing - RCA ANT3038XR | Owner/User Manual - Page 5
the provided #10 screws and nuts to attach the "V" to each side of boom. (See figure 9.) Step 9: Install the transformer Find the downlead connection on the bottom of the front section of the antenna, just beyond the reflector booms. Place two washers on each of the studs. Place a #10 nut on - RCA ANT3038XR | Owner/User Manual - Page 6
gently tap them into the ends so that they are secure. Step 11: Mount the antenna to a mast #10 Nuts Boom brace Clamp insert Main boom Clamp insert Fig. 12 the mast clamp inserts on the inside of the mast clamps on the antennas as shown in figure 12. Then insert the U-bolts into the mast clamps and - RCA ANT3038XR | Owner/User Manual - Page 7
by the wind. Ground the antenna and mast per the accompanying grounding instructions. Antenna Removal Removal of the antenna should be exactly the reverse of the installation instructions. Please, for your own safety, follow the instructions for installing the antenna starting with the last step - RCA ANT3038XR | Owner/User Manual - Page 8
does not cover product purchased, serviced or used outside the United apply to costs incurred for installation, removal or reinstallation of the 'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge, NY 11788 CANADA: Audiovox
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
ANT3038XR
Outdoor Antenna
User’s Guide
Para obtener instrucciones en español,
consulte la página 9.
Mast
(Not Included)
Reflector
Booms
Front Boom
Boom Brace
Large Boom
Rear Boom
Step 1: Unpack
Remove all three sections of the antenna and the hardware bag from package.
Make sure the following parts are in the package:
•
(3) Antenna sections (rear, large/middle, and front booms)
•
(1) Boom brace
•
(2) Reflector booms
•
(1) Hardware bag
The hardware bag contains the following pieces:
(2) U-Bolts
(4) 1/4” Flange nuts
(2) Mast clamp inserts
(5) End caps
(10) #10 Flange nuts
(4) #10 Screws
(8) #10 Washers
(1) Matching transformer
BEFORE YOU START!!!
Please read the IMPORTANT SAFETY INFORMATION sheet included in this
package.
Assembling the ANT3038XR
Fig.1: ANT3038XR fully assembled
(mast not inclued)
English