RCA VR637HF User Guide - Page 14

RCA VR637HF - Hi-Fi VCR Manual

Get RCA VR637HF - Hi-Fi VCR PDF manuals and user guides
UPC - 034909121351
View all RCA VR637HF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Chapter 1: Connections & Setup ON•OFF PAUSE PLAY REC Turns the power of the active device (either the TV or VCR) on or off. Pauses playback and recording in VCR mode. Starts tape playback in VCR mode. Starts recording in VCR mode. REV Rewinds a tape. In Playback mode, pressing and holding REV starts reverse scan playback. In Stop mode, pressing REV fast-rewinds. SEARCH In stop mode, displays Index Search and Go-To Search menus on-screen. Press this button once to display the Index Search menu and a second time to display the Go-To Search menu. In playback mode, press the SEARCH button to activate the Commercial Scan feature. Each press after that advances the tape's playback through 30 seconds of recorded material (up to five minutes). SPEED Changes the recording speed (either SP or SLP). STOP Stops the active function of the VCR including tape playback, recording rewinding, and fast-forwarding. Pressing the STOP button for several seconds also ejects an inserted tape. TRACK +/- (up and down) buttons Allows the manual reduction of streaks which may appear on the picture during regular or slow-motion playback. Reduces picture "jitter" during play-pause mode. TV Puts the remote control in TV mode. This button will automatically turn on most RCA, GE, Proscan, and Scenium TVs. VCR Puts the remote control in VCR mode. Decreases or increases the TV volume. VOL+/VOL- buttons Using the INPUT Button Use the INPUT button to toggle through the available Video Input Channel sources (Video1 and Video2) and regular broadcast signals. The Video Input Channels allow you to view images from a device connected to your VCR (like a camcorder). 1. 2. 3. Press the remote control's VCR button to activate VCR mode. Make sure that the VCR is turned ON. Press the remote control's INPUT button to tune to the Video Input Channel. Video1 represents the rear A/V jacks and Video2 represents the front A/V jacks. Press the INPUT button again to tune back to the broadcast signal you were previously watching through the VCR. 12 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Chapter 1: Connections & Setup
12
Chapter 1
ON•OFF
Turns the power of the active device (either the TV or VCR) on or off.
PAUSE
Pauses playback and recording in VCR mode.
PLAY
Starts tape playback in VCR mode.
REC
Starts recording in VCR mode.
REV
Rewinds a tape. In Playback mode, pressing and holding REV starts reverse scan
playback. In Stop mode, pressing REV fast-rewinds.
SEARCH
In stop mode, displays
Index Search and Go-To Search
menus on-screen. Press this
button once to display the
Index Search
menu and a second time to display the
Go-To Search
menu. In playback mode, press the SEARCH button to activate the Commercial Scan feature.
Each press after that advances the tape’s playback through 30 seconds of recorded material (up
to five minutes).
SPEED
Changes the recording speed (either SP or SLP).
STOP
Stops the active function of the VCR including tape playback, recording rewinding, and
fast-forwarding. Pressing the STOP button for several seconds also ejects an inserted tape.
TRACK +/– (up and down) buttons
Allows the manual reduction of streaks which may
appear on the picture during regular or slow-motion playback. Reduces picture “jitter” during
play-pause mode.
TV
Puts the remote control in TV mode. This button will automatically turn on most RCA, GE,
Proscan, and Scenium TVs.
VCR
Puts the remote control in VCR mode.
VOL+/VOL- buttons
Decreases or increases the TV volume.
Using the INPUT Button
Use the INPUT button to toggle through the available Video Input Channel sources (Video1 and
Video2) and regular broadcast signals. The Video Input Channels allow you to view images
from a device connected to your VCR (like a camcorder).
1.
Press the remote control’s VCR button to activate VCR mode. Make sure that the VCR is
turned ON.
2.
Press the remote control’s INPUT button to tune to the Video Input Channel.
Video1
represents the rear A/V jacks and
Video2
represents the front A/V jacks.
3.
Press the INPUT button again to tune back to the broadcast signal you were previously
watching through the VCR.