Ricoh C220N Operating Instructions - Page 17

Unpacking, Environments to Avoid, Power Source - specification

Page 17 highlights

Installing the Printer ❖ Environments to Avoid Important ❒ Areas exposed to direct sunlight or strong light ❒ Dusty areas ❒ Areas with corrosive gases ❒ Areas that are excessively cold, hot, or humid ❒ Locations near air conditioners or humidifiers 2 ❒ Locations near other electronic equipment ❒ Locations subject to frequent strong vibration ❖ Power Source Connect the power cable to a power source of the following specification: • 220 - 240 V, 50/60 Hz, 6 A or more • 120 V, 60 Hz, 11 A or more Unpacking To protect it from shock and vibration during transit, this printer comes packaged in cushioning foam and secured with tape. Remove these protective materials after bringing the machine to where it will be installed. R WARNING: • Do not incinerate used toner or toner containers. Toner dust might ig- nite when exposed to an open flame. Dispose of used toner containers in accordance with local regulations. • Do not store toner, used toner, or toner containers in a place with an open flame. The toner might ignite and cause burns of a fire. R CAUTION: • Keep toner (used or unused) and toner containers out of reach of children. • If toner or used toner is inhaled, gargle with plenty of water and move into a fresh air environment. Consult a doctor if necessary. • If toner or used toner gets into your eyes, flush thoroughly with eyewash or water. Consult a doctor if necessary. • If toner or used toner is swallowed, dilute by drinking a large amount of wa- ter. Consult a doctor if necessary. • When moving the printer, use the inset grips on both sides. The printer will break or cause injury if dropped. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122

Installing the Printer
7
2
Environments to Avoid
Important
Areas exposed to direct sunlight or strong light
Dusty areas
Areas with corrosive gases
Areas that are excessively cold, hot, or humid
Locations near air conditioners or humidifiers
Locations near other electronic equipment
Locations subject to frequent strong vibration
Power Source
Connect the power cable to a power source of the following specification:
220 - 240 V, 50/60 Hz, 6 A or more
120 V, 60 Hz, 11 A or more
Unpacking
To protect it from shock and vibration during transit, this printer comes pack-
aged in cushioning foam and secured with tape. Remove these protective mate-
rials after bringing the machine to where it will be installed.
R
WARNING:
R
CAUTION:
Do not incinerate used toner or toner containers. Toner dust might ig-
nite when exposed to an open flame. Dispose of used toner containers
in accordance with local regulations.
Do not store toner, used toner, or toner containers in a place with an
open flame. The toner might ignite and cause burns of a fire.
Keep toner (used or unused) and toner containers out of reach of children.
If toner or used toner is inhaled, gargle with plenty of water and move into
a fresh air environment. Consult a doctor if necessary.
If toner or used toner gets into your eyes, flush thoroughly with eyewash or
water. Consult a doctor if necessary.
If toner or used toner is swallowed, dilute by drinking a large amount of wa-
ter. Consult a doctor if necessary.
When moving the printer, use the inset grips on both sides. The printer will
break or cause injury if dropped.