Samsung DV42H5600EG/AC User Manual Ver.1.0 (English, French, Spanish) - Page 18

Connecting the inlet hose

Get Samsung DV42H5600EG/AC PDF manuals and user guides View all Samsung DV42H5600EG/AC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Connecting the inlet hose The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses. 1. Turn the cold water faucet off. 2. Attach the brass female end of the Y connector (A) to the cold water B faucet. 3. Attach the straight end of long hose (B) to the Y connector. 4. Using pliers, tighten the coupling with an additional two-thirds turn. A If the Y connector cannot be attached directly to the cold water faucet, the short hose must be used. C (If space permits, please skip steps 5 to 8, and go directly to step 9.) 5. Attach the short inlet hose (C) to the cold water faucet. Screw on the coupling by hand until it is seated on the faucet. A 6. Using the pliers, tighten the coupling with an additional two-thirds turn. 7. Attach the Y connector (A) to the brass male end of the small hose. Screw on the coupling by hand until it is seated on the connector. 8. Using the pliers, tighten the coupling with an additional two-thirds turn. 9. Attach the angled end of long hoses to the fill valve at the bottom of the dryer rear frame. Screw on the coupling by hand until it is seated on the fill valve connector. 10. Using pliers, tighten the coupling with an additional two-thirds turn. 11. Attach the washer hose (D) to the other side of the Y connector (A). Screw on the hose coupling until it is tight. Using pliers, tighten the coupling with an additional two thirds turn. A 12. Check that the water faucets are on. D 13. Check for leaks around the Y connector, faucets and hoses. When you tighten the coupling with pliers, do not overtighten. This may damage the coupling. DV6000HA_DC68-03380A.indd 18 English - 18 2013-12-19 �� 1:07:49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
English - 18
Connecting the inlet hose
The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.
1.
Turn the cold water faucet off.
2.
Attach the brass female end of the
Y connector (A)
to the cold water
faucet.
3.
Attach the straight end of
long hose (B)
to the Y connector.
4.
Using pliers, tighten the coupling with an additional two-thirds turn.
A
B
If the Y connector cannot be attached directly to the cold water
faucet, the short hose must be used.
(
If space permits,
please skip steps 5 to 8, and go directly to step 9.)
5.
Attach the
short inlet hose (C)
to the cold water faucet.
Screw on the coupling by hand until it is seated on the faucet.
6.
Using the pliers, tighten the coupling with an additional two-thirds
turn.
7.
Attach the
Y connector (A)
to the brass male end of the small hose.
Screw on the coupling by hand until it is seated on the connector.
8.
Using the pliers, tighten the coupling with an additional two-thirds
turn.
C
A
9.
Attach the angled end of long hoses to the fill valve at the bottom of
the dryer rear frame. Screw on the coupling by hand until it is seated
on the fill valve connector.
10.
Using pliers, tighten the coupling with an additional two-thirds turn.
11.
Attach the
washer hose (D)
to the other side of the
Y connector (A)
.
Screw on the hose coupling until it is tight. Using pliers, tighten the
coupling with an additional two thirds turn.
12.
Check that the water faucets are on.
13.
Check for leaks around the Y connector, faucets and hoses.
D
A
When you tighten the coupling with pliers, do not overtighten. This may damage the coupling.
DV6000HA_DC68-03380A.indd
18
2013-12-19
�� 1:07:49