Samsung DW80R7060UG User Manual - Page 18

° fitting A, hose B, seal C, nut D, B, STEP 11, Securing the Dishwasher.

Get Samsung DW80R7060UG PDF manuals and user guides View all Samsung DW80R7060UG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Installation 3. Use the provided nut connector to connect the water hose to the dishwasher. Follow these steps: 01 02 A 03 E B C D F 01 Disconnect the 90° fitting (A) from the hose (B). 02 Remove the seal (C) and the nut (D) from the 90° fitting. 03 From the provided nut connector, separate the seal (E) and the nut (F), and then assemble them to the 90° fitting as shown in the figure. You must insert the smaller side of the seal. 4. Then, insert the 3/4" 90 degree fitting into the inlet valve (See Figure 4-B). Tighten until the 3/4" fitting is tight. Do not over tighten. 5. Detach the Velcro strips that secure the drain hose to the back of the dishwasher. Rollout the hose. Make sure there are no kinks and that the hose is not bent at any extreme angles that could constrict the flow of water. 6. Remove the junction box cover located at the bottom front right of the dishwasher using a screwdriver, and then Install the strain relief (Figure 4-C). Make sure to keep the junction box cover you removed. It is used in STEP 11, Wiring Connections. 7. If the countertop is made of wood or a material that is not damaged by drilling, attach the two (2) Installation brackets that were supplied with the dishwasher using the supplied screws (Figure 4-A). They will be used in STEP 9, Securing the Dishwasher. If the drain hose needs to go to the right of the dishwasher, secure the drain hose into the drain hose bracket, mounted on the base. The drain hose bracket can be adjusted in 3 positions. To adjust the height of the drain hose bracket, gently squeeze the bracket and turn it too the left. Insert the bracket in the desired position and turn it to the right to lock it into place. Installation 18 English DW8000R_DD68-00210A-00_EN.indd 18 4/25/2019 11:10:42 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Installation
Installation
English
18
3.
Use the provided nut connector to connect the water hose to the dishwasher.
Follow these steps:
01
02
03
A
B
C
E
D
F
01
Disconnect the
90° fitting (A)
from the
hose (B)
.
02
Remove the
seal (C)
and the
nut (D)
from the 90° fitting.
03
From the provided nut connector, separate the
seal (E)
and the
nut (F)
, and then
assemble them to the 90° fitting as shown in the figure. You must insert the smaller
side of the seal.
4.
Then, insert the
3
/
4
" 90 degree fitting into the inlet valve (See
Figure 4-B
). Tighten until
the
3
/
4
" fitting is tight. Do not over tighten.
5.
Detach the Velcro strips that secure the drain hose to the back of the dishwasher. Roll-
out the hose. Make sure there are no kinks and that the hose is not bent at any extreme
angles that could constrict the flow of water.
6.
Remove the junction box cover located at the bottom front right of the dishwasher
using a screwdriver, and then Install the strain relief (
Figure 4-C
). Make sure to keep
the junction box cover you removed. It is used in
STEP 11
, Wiring Connections.
7.
If the countertop is made of wood or a material that is not damaged by drilling, attach
the two (2) Installation brackets that were supplied with the dishwasher using the
supplied screws (
Figure 4-A
). They will be used in
STEP 9
, Securing the Dishwasher.
If the drain hose needs to go to the
right of the dishwasher, secure the
drain hose into the drain hose bracket,
mounted on the base.
The drain hose bracket can be adjusted
in 3 positions. To adjust the height
of the drain hose bracket, gently
squeeze the bracket and turn it too the
left. Insert the bracket in the desired
position and turn it to the right to lock
it into place.
DW8000R_DD68-00210A-00_EN.indd
18
4/25/2019
11:10:42 AM