Samsung NE58K9850WS/AA Installation Guide - Page 5

Caution

Get Samsung NE58K9850WS/AA PDF manuals and user guides View all Samsung NE58K9850WS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

01 PREPARING TO INSTALL THE RANGE CHECKING THE INSTALLATION SITE Clearances and dimensions To install the range, refer to the following figure. CAUTION CAUTION This range has been designed to comply with the maximum allowable wood cabinet temperatures of 194 °F. Make sure the wall covering, countertops, and cabinets around the range can withstand the heat (up to 194 °F) generated by the range. If not, discoloration, delamination, or melting may occur. SLIDE-IN CUTOUT FREESTANDING CUTOUT Hatched Faces should be flat and leveled. 3" 24" 1" min. 3" 1/2" min. 4-1/2" 36"~36-3/4" 23-3/16" 6-5/16" 29-15/16" 31" 35-7/8" 26-5/16" 28-5/8" 24-11/16" A 48" 26-5/16" 23-3/16" 25" B 6" A 3" 25" 24" 3" 6" B A A : Cabinet opening min 30" (76.2 cm) B : Acceptable electrical outlet area If your cabinets are over 36-3/4" high, you must install this range on a hard, heat resistant support that raises the surface of the range so that it is about even with the countertop. CAUTION CAUTION You must use the rear filler kit to install the range in a freestanding cutout cabinet. For more information, see "Optional rear filler kit" as shown below. Optional rear filler kit Used to fill gap between the range back and wall. Adds a filler strip to the rear of the range. This kit can only be used when the opening in the countertop is 25" deep. If the countertop depth is greater than 25", there will be a gap between the filler kit and the back wall. English - 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
CHECKING THE INSTALLATION SITE
Clearances and dimensions
To install the range, refer to the following figure.
CAUTION
CAUTION
This range has been designed to comply with the maximum
allowable wood cabinet temperatures of 194 °F. Make sure the wall covering,
countertops, and cabinets around the range can withstand the heat (up to 194 °F)
generated by the range. If not, discoloration, delamination, or melting may occur.
SLIDE-IN CUTOUT
FREESTANDING CUTOUT
A
B
36"~36-3/4"
31"
4-1/2"
23-3/16"
6-5/16"
24-11/16"
48"
28-5/8"
26-5/16"
29-15/16"
26-5/16"
Hatched Faces should
be flat and leveled.
35-7/8"
23-3/16"
1/2" min.
25"
6"
3"
24"
3"
1" min.
A
B
6"
25"
3"
24"
3"
A : Cabinet opening
min 30" (76.2 cm)
B : Acceptable electrical outlet area
If your cabinets are over 36-3/4" high, you must install this range on a hard, heat
resistant support that raises the surface of the range so that it is about even with
the countertop.
CAUTION
CAUTION
You must use the rear filler kit to install the range in a
freestanding cutout cabinet. For more information, see “Optional rear filler kit” as shown
below.
Optional rear filler kit
Used to fill gap between the range back and wall. Adds a filler strip to the rear of the
range. This kit can only be used when the opening in the countertop is 25” deep.
If the countertop depth is
greater than 25", there will
be a gap between the filler kit
and the back wall.
English - 5
01
PREPARING TO INSTALL THE RANGE