Samsung NE58K9850WS/AA Installation Guide - Page 9

Step 2. Accessing The Power Cord Connection

Get Samsung NE58K9850WS/AA PDF manuals and user guides View all Samsung NE58K9850WS/AA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

02 CONNECTING THE POWER A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50 amp range cord is not recommended but if used, it should be marked for use with nominal 13⁄8" diameter connection openings. Care should be taken to center the cable and strain relief within the knockout hole to keep the edge from damaging the cable. • Because range terminals are not accessible after the range is in position, a flexible service conduit or cord must be used. NOTE If conduit is being used, go to Step 4 on page 12. ALL NEW BRANCH-CIRCUIT CONSTRUCTIONS, MOBILE HOMES, RECREATIONAL VEHICLES, AND INSTALLATIONS WHERE LOCAL CODES DO NOT ALLOW GROUNDING THROUGH NEUTRAL, REQUIRE A 4-CONDUCTOR UL-LISTED RANGE CORD. STEP 2. ACCESSING THE POWER CORD CONNECTION Loosen and then remove the rear access cover screw with a screwdriver. Remove the rear access cover by pull right and then out. The terminal block will then be accessible. Terminal block Access cover Specified power-supply-cord kit rating Range rating, watts 120/240 volts 120/208 volts 3-wire 3-wire Specified rating of power-supply-cord kit, amperes Diameter (inches) of range connection opening Power cord Conduit 8750 - 16500 7801 - 12500 40 or 50 A 13/8" 11/8" For power cord installations, go to page 10. For conduit installations, go to page 12. English - 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
A range cord rated at 40 amps with 125/250 minimum volt range is required. A 50
amp range cord is not recommended but if used, it should be marked for use with
nominal 1
3
⁄
8
" diameter connection openings. Care should be taken to center the
cable and strain relief within the knockout hole to keep the edge from damaging the
cable.
•
Because range terminals are not accessible after the range is in position, a flexible
service conduit or cord must be used.
NOTE
If conduit is being used, go to Step 4 on page 12.
ALL NEW BRANCH-CIRCUIT CONSTRUCTIONS, MOBILE HOMES,
RECREATIONAL VEHICLES, AND INSTALLATIONS WHERE LOCAL
CODES DO NOT ALLOW GROUNDING THROUGH NEUTRAL,
REQUIRE A 4-CONDUCTOR UL-LISTED RANGE CORD.
STEP 2. ACCESSING THE POWER CORD CONNECTION
Loosen and then remove the rear access cover screw with a screwdriver. Remove
the rear access cover by pull right and then out. The terminal block will then be
accessible.
Access cover
Terminal block
Specified power-supply-cord kit rating
Range rating, watts
Specified rating of
power-supply-cord
kit, amperes
Diameter (inches) of range
connection opening
120/240 volts
3-wire
120/208 volts
3-wire
Power cord
Conduit
8750 - 16500
7801 - 12500
40 or 50 A
1
3
/
8
"
1
1
/
8
"
For power cord installations, go to page 10. For conduit installations, go to page 12.
English - 9
02
CONNECTING THE POWER