Samsung SMH1622B Installation Instructions - Page 14

C1. Adapting Microwave Blower, For Outside Back Exhaust

Get Samsung SMH1622B PDF manuals and user guides View all Samsung SMH1622B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Step-by-step installation guide C. Outside back exhaust (horizontal duct) C1. Adapting microwave blower for outside back exhaust 1. Remove and save screw that holds blower Plate to microwave. Screw 2. Lift up the Blower Plate. Blower Motor Back of Microwave Blower Plate Screw 3. Carefully pull out the blower unit. The wires will extend far enough to allow you to adjust the blower unit. BEFORE: Fan Blade Openings Facing Forward End B End A CAUTION: Do not touch blade of blower to prevent cracking and breaking. Hold outer case when the blower is removed and re-installed. 4. Rotate blower unit counterclockwise 180 °. Before Rotation After Rotation 5. Place the blower unit back into the opening. AFTER: Fan Blade Openings Facing Back End A End B CAUTION: Do not pull or stretch the blower unit wiring. Make sure the wires are not pinched. NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven. 6. Close the blower plate and attach the exhaust adaptor to the rear of the oven by sliding it into the guides at the top center of the back of the oven. Push in securely until it is in the lower locking tabs. Take care to assure that the damper hinge is installed so that it is at the top and that the damper swings freely. Adaptor Guide Back of Microwave Guide blower plate screw From Blower motor screw (after attached the exhaust adaptor) Back of Microwave Back of Microwave 3. IN A B C D E. A Yo ou • • • C ca 14 SMH8165_XAA DE68-03587A-04-EN_120725.indd 14 2012-07-25 �� 8:05:31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
14
Step-by-step installation guide
C.
OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
C1. ADAPTING MICROWAVE BLOWER
FOR OUTSIDE BACK EXHAUST
1
.
Remove and save screw that holds blower Plate
to microwave.
2
.
Lift up the Blower Plate.
Screw
Blower Motor
Back of
Microwave
Blower Plate Screw
3
.
Carefully pull out the blower unit. The wires will
extend far enough to allow you to adjust the
blower unit.
BEFORE: Fan Blade
Openings Facing Forward
End B
End A
CAUTION
:
Do not touch blade of blower to prevent
cracking and breaking. Hold outer case when the
blower is removed and re-installed.
4
.
Rotate blower unit counterclockwise 180 °.
Before Rotation
After Rotation
Back of Microwave
Back of Microwave
5
.
Place the blower unit back into the opening.
AFTER: Fan Blade Openings
Facing Back
End B
End A
CAUTION
:
Do not pull or stretch the blower unit
wiring. Make sure the wires are not pinched.
NOTE: The blower unit exhaust openings
should match exhaust openings on rear of
microwave oven.
6
.
Close the blower plate and attach the exhaust
adaptor to the rear of the oven by sliding it
into the guides at the top center of the back
of the oven. Push in securely until it is in the
lower locking tabs. Take care to assure that the
damper hinge is installed so that it is at the top
and that the damper swings freely.
blower plate screw
Adaptor
Guide
Back of
Microwave
Guide
From Blower motor screw
(after attached the exhaust adaptor)
IN
A
B
C
D
E
.
A
Yo
ou
•
•
•
C
ca
3.
SMH8165_XAA DE68-03587A-04-EN_120725.indd
14
2012-07-25
�� 8:05:31