Samsung WF337AAR User Manual (ENGLISH) - Page 10

Installing your washer

Get Samsung WF337AAR PDF manuals and user guides View all Samsung WF337AAR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

installing your washer 2. Insert new rubber washer (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings. 3. Check the inlet hose to ensure a washer is inside each fill Cold hose. Thread the inlet hoses to the HOT and COLD faucet connections. On the other end of the hose, check for one rubber washer per hose and install each fill hose to the water valve. Make sure the hose with the Hot printed line is attached to the HOT faucet. Tighten by hand until snug, then two-thirds of a turn with pliers. Hot Rubber washer For correct water use, connect both HOT and COLD water valves. If one is not connected, an "nF" (no fill) error can occur. Cold printed Hot printed 4. Turn on the "HOT" and "COLD "water supply and check all connections at the water valve and the faucet for leaks. 5. Plug the power cord into a 3-Prong, well grounded 120 volt 60 Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker. Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded receptacle. 6. Slide your washer into position. 7. Level your washer by turning the leveling legs in or out as necessary by hand or wrench included with your washer. When your washer is level, tighten the nuts using the wrench or (-) driver. Your Washer must be leveled on all four sides. A carpenter's level should be used on all four corners of your Washer. It's a good idea after the first dozen washes to recheck your washer's levelness. 10_ Installing your washer WF337A-02440A-06_EN.indd 10 2007-08-10 ¿ÀÈÄ 2:07:40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
10_
Installing your washer
2.
Insert new rubber washer (supplied) into each end of the
inlet hoses. Firmly seat the washers in the couplings.
3.
Check the inlet hose to ensure a washer is inside each fill
hose.
Thread the inlet hoses to the HOT and COLD faucet
connections.
On the other end of the hose, check for one rubber washer
per hose and install each fill hose to the water valve. Make
sure the hose with the Hot printed line is attached to the
HOT faucet. Tighten by hand until snug, then two-thirds of a
turn with pliers.
For correct water use, connect both HOT and COLD water
valves. If one is not connected, an “nF” (no fill) error can
occur.
4.
Turn on the “HOT” and “COLD “water supply and check all
connections at the water valve and the
faucet for leaks
.
5.
Plug the power cord into a 3-Prong, well grounded 120 volt
60 Hz approved electrical outlet protected by a 15-amp
fuse or comparable circuit breaker.
Your washer is grounded through the third prong of the
power cord when plugged into a three-prong grounded
receptacle.
6.
Slide your washer into position.
7.
Level your washer by turning the leveling legs in or out as
necessary by hand or wrench included with your washer.
When your washer is level, tighten the nuts using the
wrench or (-) driver.
Your Washer must be leveled on all four sides. A
carpenter’s level should be used on all four corners of
your Washer. It’s a good idea after the first dozen washes
to recheck your washer’s levelness.
installing your washer
Cold
Hot
Cold printed
Hot printed
Rubber washer
WF337A-02440A-06_EN.indd
10
2007-08-10
¿ÀÈÄ 2:07:40