Sanyo PLC-XF47 Owners Manual - Page 19

Terminals of Projector, NOTES ON ORDERING OR USING, OPTIONAL INTERFACE BOARD - for sale

Get Sanyo PLC-XF47 - XGA LCD Projector PDF manuals and user guides
UPC - 086483068959
View all Sanyo PLC-XF47 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Installation Terminals of Projector This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired combinations of input sources just by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector. 4 TERMINAL SLOTS (Factory set) SERIAL PORT IN DIGITAL (DVI-D) ANALOG DVI / D-sub 15 Terminal INPUT 1 SERIAL PORT OUT R/C JACK USB G B R H/HV V VIDEO/Y Pb/Cb Pr/Cr S-VIDEO ▼ L INPUT 2 5-BNC / VideoTerminal INPUT 3 INPUT 4 INPUT/OUTPUT RESET TERMINALS Replacement of Terminal ✔Note: • In the replacement of terminal board, the MAIN ON/OFF switch should be OFF position. 1 Remove 2 Screws on a terminal. 2 Pull out the terminal by holding handle. 3 Replace the terminal. Insert a new terminal along Guide to fit Plug into Socket. 4 Tighten screws to secure the terminal. NOTES ON ORDERING OR USING OPTIONAL INTERFACE BOARD When ordering or using Optional Interface Board (Terminal Board), contact your sales dealer. When contacting the sales dealer, tell the Option Control Number (Op.cont.No.) in the menu that is located on the bottom of the information menu.(See page 28) Plug Screws Guide Socket Figure shows D-sub 15 terminal. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
19
Terminals of Projector
This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity
of signals from computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired
combinations of input sources just by changing Terminal Boards.
For Terminal Boards, contact sales dealer
where you purchased a projector.
Pull out
the terminal by holding handle.
Remove 2 Screws on a terminal.
1
2
Tighten screws to secure the terminal.
Replace the terminal. Insert a new terminal along
Guide to fit Plug into Socket.
3
4
ANALOG
G
B
R
H/HV
V
DIGITAL (DVI-D)
INPUT 1
R/C JACK
USB
RESET
INPUT 2
INPUT 3
INPUT 4
SERIAL PORT IN
SERIAL PORT OUT
L
VIDEO/Y
Pb/Cb
Pr/Cr
S-VIDEO
▼
INPUT/OUTPUT
TERMINALS
Screws
Guide
Socket
Plug
Figure shows D-sub 15 terminal.
DVI / D-sub 15 Terminal
5-BNC / VideoTerminal
4 TERMINAL SLOTS (Factory set)
NOTES ON ORDERING OR USING
OPTIONAL INTERFACE BOARD
When ordering or using Optional Interface Board (Termi-
nal Board), contact your sales dealer. When contacting the
sales dealer, tell the Option Control Number (Op.cont.No.)
in the menu that is located on the bottom of the information
menu.(See page 28)
✔
Note:
• In the replacement of terminal board, the MAIN
ON/OFF switch should be OFF position.
Replacement of Terminal
Installation