Sanyo WXU300 Instruction Manual, PLC-WXU300 Network Operation
Sanyo WXU300 - WXGA LCD Projector 720p Manual
 |
UPC - 086483074226
View all Sanyo WXU300 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sanyo WXU300 manual content summary:
- Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 1
This is the manual for the Network function. Read this manual thoroughly to operate the Network function. First, read the owner's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the owner's manuals should be followed - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 2
the equipment unless otherwise speci- fied in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Model Numbers : PLC-WXU300 Trade Name : Sanyo Responsible party : SANYO FISHER COMPANY Address : 21605 Plummer Street - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 3
Safety instructions CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable immediately and inspect the unit. Using the projector with failure may cause fire or other accidents. ● If you remotely use the projector via networks, carry out a - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 4
Compliance...2 Federal Communications Commission Notice 2 Safety instructions...3 Table of contents...4 Chapter 1 Preparation 5 Features...6 Required operating environment for computers 7 Network specifications of the projector...7 Flow of installation...9 Notice about installing Software - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 5
Chapter 1 Preparation Describes features and operating environment of this projector. 1 ENGLISH - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 6
projector functions PC1 PC2 such as power status, lamp status, input mode, signal condition, lamp-use time, etc. through the network by using when a lamp abnor- mality or power failure occurs with the projector. This mes- sage describes how to solve the PC3 PC4 cause of the problems. You - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 7
Vista Macintosh : 256MB or more (512MB is recommended) 100MB or more CD-ROM drive Support one of following resolutions; VGA (640 x 480), SVGA(800 x 600), XGA(1,024 projector. If you do not use the func- tion E-mail Alert, this application is not required. Network specifications of the projector - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 8
differ from the actual operation depending on your computer environment. Use of this manual This manual does not provide the description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 9
in CD-ROM on each computer which will be operated. Refer to the owner's manual of PJ Network Manager. Notice about installing Software CD-ROM It is available for controlling and setting of the projector by using the web browser without installing any software. So it is not required to install the - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 10
Chapter 1 Preparation 10 - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 11
Chapter 2 Setup Procedures Describes how to configure the network. 2 ENGLISH 11 - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 12
is sending or receiving the data. LAN Cable LINK Lamp (Green) Light green when the projector is connected to the network correctly. Network configuration Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser. Refer to "3. Basic setting and - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 13
DHCP function On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, Gateway and DNS are automatically set according to your network environment *1. IP address Sets IP address of the projector Subnet Sets Subnet mask. Normally sets 255.255.255 - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 14
code if you use the projector via the networks. The Network PIN code can be set also through the networks. See "3. Basic setting and operation" ➔ "Initial setting" ➔ "Network PIN code setting" (p.23). Network PIN code Network PIN code screen Network information Select "Network information" in the - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 15
factory default Network factory default 1. Select "Network factory default" in the Network menu and press SELECT button. 2. A confirmation box appears and select "Yes" and then press SELECT button. 3. Another confirmation box appears and select "Yes" and then - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 16
Chapter 2 Setup Procedures Wired LAN factory default settings Parameter IP CONFIGURATION LAN 1 MANUAL SELECTED LAN LAN 2 DHCP LAN 3 MANUAL IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100 SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0 GATEWAY - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 17
Chapter 3 Basic Setting and Operation Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 3 ENGLISH 17 - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 18
and then click OK (Log in) button. * The entering User Name must be "user" and it can not be changed. [Note] When accessing the projector for the first time or the Network PIN code "0000" is set, the auto-login will be performed and the next main setting page is displayed. 18 - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 19
Login the setting page of the projector [3] Display of main setting page The following main setting page will be menu tab. Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected menu. ENGLISH 19 - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 20
Chapter 3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 21
Radio button setting Select an item by selecting a radio button. Check box setting Select items by ticking on check boxes. How to use the setting page ENGLISH 21 - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 22
Language Switches display language on the setting page. English or Japanese. Model name........Indicates the model name of the projector Network PIN code.......Sets the Network PIN code to login the setting page (+p.23) PJLink Switches PJLink password authentication on or off (+p.23) Password - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 23
characters can be used for the password. What's PJLink? The projectors equipped with PJLink function can be used together on the same network, regardless of model english/. PJLink Notice The projector is compliant with PJLink Standard Class 1 of JBMIA, and it supports all commands defined by - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 24
....Sets DHCP or Manual IP address Sets IP address of the projector Subnet mask.......Sets Subnet projector name. You can access with this projector name from any computers in your network. If you do not use the DNS server, access with the assigned IP address to the projector. * All the network - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 25
if it detects an abnormality on the projector or run out of the life span of the lamp. Click E-mail Setting on the main menu Network setting page correctly. ✐ You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your net- work environment. ✐ The projector - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 26
of alert mail" described on the next page. Option ✐ "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 27
and ask servicing to qualified service personnel. MCI 3.3V OK MAIN ALL NG Error information ✐ The projector lamp was turned off, because the projector power circuit failed. Unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the problem still - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 28
name TCP/IP: 192.168.1.201 Projector Name: Proj05 It sends you following message. *The projector lamp has reached replacement time. Lamp ON 2000 h ✐ Replace it with a new lamp immediately and reset the lamp counter. If the projector is used without resetting the lamp counter, the alert mail is sent - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 29
(Simple Network Management Protocol) agent function. The SNMP consists of a manager and agents. The group which communicates information each other with SNMP is called "Community". There are two access modes in a community, Refer (read only) and Set (readwrite). This projector allows to use Refer - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 30
you tick or un-tick the check box on a page. ✐ "When PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 31
Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. 4 ENGLISH 31 - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 32
window Item Description PJ status Power Displays the status of the lamp. (ON, OFF, On starting up, On cooling down) Status Displays the status of the projector's power. (Refer to next page.) Power control.........Controls the projector power by clicking the "ON" or "Standby" button. ✐ The - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 33
AC cord and ask servicing to a qualified service personnel. When a security (PIN code lock) has been set on the projector, you also cannot control it through the network. To control the projector through the network, unlock the security on the projector using with the projector's menu control - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 34
pages and select desired setting items. ✐ Please see the owner's manual of the projector to have the further information of each control item. Input This function the selected input mode, signal or functions of the projector you use, therefore, there may be different controls between the described - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 35
System This function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu button according to the input signal. Select a system and then click Set button. Available - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 36
Chapter 4 Controlling the Projector Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status. Item Description Volume Adjusts the sound volume from the speaker. (0 ~ 63) Mute Suppresses the sound. (ON, OFF) 36 - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 37
Control Image adjustment This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and to load the adjusted value, click Load button. Item Description Contrast Adjusts picture contrast (0~ 63) Brightness Adjusts picture - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 38
function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current etc. or Mode1 - Mode5 which are the customized mode created by using the "Mode Store" function described below. Auto PC adj..........Performs - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 39
the sub menu [Screen setting] or [Setting] and then set up each setting. Screen setting This function is to adjust the screen mode of the projector. The values in the text box represent the current screen status. Item Description Screen Switches the screen mode. (Normal, True, Full, Wide, Zoom - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 40
display of projector's on- OFF) Auto keystone.....Sets Auto Keystone mode. (Auto, Manual, OFF) Background.........Sets the screen background when no signal Lamp control......Selects lamp control mode. (Normal, Eco) Lamp life control Selects lamp life control mode (Mode1, Mode2) when the total use - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 41
the time to indicate the filter warning message on the screen. (OFF, 100H, 200H, 300H) Factory default..........Sets all of the projector control items to the factory default setting except the following items. Lamp Corres. Value, PJ time, Network PIN code, Network setting * This function is - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 42
the filter. Indication of the lamp status Icon display/background Status White-Yellow/Blue Lamp on (Normal) White-Yellow/Red Lamp on (Lamp is being used over a specified use time, replace lamp immediately) Gray/Blue Gray/Red Lamp off (Normal) Lamp off (Lamp is being used over a specified use - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 43
Chapter 5 Appendix Connection examples Use of telnet Web browser setting Technical data Q & A 5 ENGLISH 43 - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 44
the projector (PJ01) to the control computer (PC05) via the hub. Hub To another network Computer Name: PC05 IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway : DNS : Projector : ✐ When the projector is connected to the computer directly without hub, the - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 45
of connection The gateway (Router) installed in the network Connecting the projector (PJ01) to the control computer (PC05) : PC10 : 192.168.10.10 : 255.255.255.0 : 192.168.10.1 : 192.168.201.1 Network Group: 192.168.10.x Computer Name IP Address Subnet Mask Default Gateway DNS : PC51 : 192.168.10 - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 46
on your computer. Normally, the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of Windows XP Professional.) 1. S elect Run... submenu from Start menu on the computer. Type - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 47
C0C Audio Mute off C1C Menu display on C1D menu display off *1 F urther instructions about the telnet application, please see the on-line guide on your computer. *2 The password is a Network PIN code decided item "Network PIN code setting" (☞pp.14, 23). If the authentication of the entered - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 48
enable the JavaScript, please see further instructions on the next page. Proxy setting In some cases, your web browser is set up to use the proxy server for the internet or intranet connection. In this case, when you install this projector into the local network, you should set up the proxy setting - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 49
Examples: OS/Browsers Windows XP Professional Web browser setting Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level... button. On the security setting window, scroll down and find the - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 50
proxy server address and port correctly in the proxy settings window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with UTP cross cable, this must be unchecked - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 51
to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration. Enter the proxy server address and port number correctly on HTTP Proxy item. For further instruction please consult your - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 52
area network environment to which the projector is connected. - Using proxy server To use an external internet connection from the local area network, check Web Proxy Server window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the items Web Proxy - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 53
function on the login page (☞ p.23). 2. Please use the IP filtering function provided with the gateway (router) to restrict the accessing from the computer. For further information please con- sult your network administrator. Q C an I access the projector installed on the company's local area - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 54
the DHCP/BOOTP server to assign the IP address. Is it possible to use the projector in this network environment? A P ossible. This projector supports the DHCP/BOOTP server. To use this projector in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP address - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 55
the projector are correct to use the projector. Please set the Standby mode of the projector's Setting menu to "Normal". Refer to "4. Controlling the Projector" ➔ network administrator (☞ p.25). It may be required for the authentication depending on the SMTP server. This projector does not support - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 56
, they cannot establish communications each other. In this case, the router is placed in the networks to make the routing. Q Can I control the projector by using the telnet application? A Possible. Please refer to the item "Use of telnet" (☞ p.46 - 47). Q What is the MAC address assigned to the - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 57
Q&A Q Can I update the firmware of the projector. A It is possible to update the firmware through the network. It is required to have a special tool for the updating. For further information please consult your local dealer. The version number of the firmware is - Sanyo WXU300 | Instruction Manual, PLC-WXU300 Network Operation - Page 58
NETWORK OWNER'S MANUAL SO-KE5AC SANYO Electric Co., Ltd.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
 |
 |
Wired Setting
Projector Set-up and Operation
Owner’s Manual
Network Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the owner's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the owner's manuals should be followed strictly.