Home » Seagate Manuals » Hard Drives » Seagate DB35.4 » Manual Viewer

Seagate DB35.4 DB35.4 Series SATA Product Manual - Page 11

Drive specification, ST3250310CS - series hard drives

Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Drive specification Vibration, nonoperating Drive acoustics, sound power Idle** CE Seek Profile Nonrecoverable read errors Annualized Failure Rate (AFR) Warranty Contact start-stop cycles Supports Hotplug operation per the Serial ATA Revision 2.5 specification ST3250310CS 5-350 Hz: 5.0 Gs 350-500 Hz:: 1.0 Gs 2.5 bels (typical) 2.8 bels (max) 2.6 bels (typical) 2.8 bels (max) 1 per 1014 bits read 0.68% 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the "Verify Your Warranty" link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive. 50,000 at 25°C, 50% rel. humidity Yes *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. **During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and power to operational levels. DB35.4 Series SATA Product Manual, Rev. C 5

Section	Page
1.0 Introduction 1	3
1.1 About the Serial ATA interface 2	3
2.0 Drive specifications 3	3
2.1 Specification summary tables 3	3
2.2 Formatted capacity 6	3
2.2.1 LBA mode 6	3
2.3 Default logical geometry 6	3
2.4 Recording and interface technology 6	3
2.5 Physical characteristics 7	3
2.6 Seek time 7	3
2.7 Start/stop times 7	3
2.8 Power specifications 8	3
2.8.1 Power consumption 8	3
2.8.2 Conducted noise 9	3
2.8.3 Voltage tolerance 9	3
2.8.4 Power-management modes 10	3
2.9 Environmental specifications 11	3
2.9.1 Drive case temperature 11	3
2.9.2 Temperature gradient 11	3
2.9.3 Humidity 11	3
2.9.4 Altitude 11	3
2.9.5 Shock 11	3
2.9.6 Vibration 12	3
2.10 Acoustics emissions 13	3
2.11 Electromagnetic immunity 13	3
2.12 Reliability 14	3
2.12.1 Annualized Failure Rate (AFR) 14	3
2.13 Agency certification 14	3
2.13.1 Safety certification 14	3
2.13.2 Electromagnetic compatibility 14	3
2.13.3 FCC verification 15	3
2.14 Environmental protection 16	3
2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive 16	3
2.14.2 China Restriction of Hazardous Substances (RoHS) Directive 16	3
2.15 Corrosive environment 16	3
3.0 Configuring and mounting the drive 17	3
3.1 Handling and static-discharge precautions 17	3
3.2 Configuring the drive 18	3
3.3 Serial ATA cables and connectors 18	3
3.4 Drive mounting 19	3
4.0 Serial ATA (SATA) interface 21	3
4.1 Hot-Plug compatibility 21	3
4.2 Serial ATA device plug connector pin definitions 22	3
4.3 Supported ATA commands 23	3
4.3.1 Identify Device command 25	3
4.3.2 Set Features command 29	3
4.3.3 S.M.A.R.T. commands 30	3
5.0 Seagate Technology support services 31	3
Figure 1. Typical 5V startup and operation current profile 9	5
Figure 2. Typical 12V startup and operation current profile 9	5
Figure 3. Serial ATA connectors 18	5
Figure 4. Attaching SATA cabling 18	5
Figure 5. Mounting dimensions 19	5
1.0 Introduction	7
1.1 About the Serial ATA interface	8
2.0 Drive specifications	9
2.1 Specification summary tables	9
2.2 Formatted capacity	12
2.2.1 LBA mode	12
2.3 Default logical geometry	12
2.4 Recording and interface technology	12
2.5 Physical characteristics	13
2.6 Seek time	13
2.7 Start/stop times	13
2.8 Power specifications	14
2.8.1 Power consumption	14
2.8.1.1 Typical current profiles	15
2.8.2 Conducted noise	15
2.8.3 Voltage tolerance	15
2.8.4 Power-management modes	16
2.9 Environmental specifications	17
2.9.1 Drive case temperature	17
2.9.2 Temperature gradient	17
2.9.3 Humidity	17
2.9.3.1 Relative humidity	17
2.9.3.2 Wet bulb temperature	17
2.9.4 Altitude	17
2.9.5 Shock	17
2.9.5.1 Operating shock	17
2.9.5.2 Nonoperating shock	17
2.9.6 Vibration	18
2.9.6.1 Operating vibration	18
2.9.6.2 Nonoperating vibration	18
2.10 Acoustics emissions	19
2.11 Electromagnetic immunity	19
2.12 Reliability	20
2.12.1 Annualized Failure Rate (AFR)	20
2.13 Agency certification	20
2.13.1 Safety certification	20
2.13.2 Electromagnetic compatibility	20
2.13.3 FCC verification	21
2.14 Environmental protection	22
2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive	22
2.14.2 China Restriction of Hazardous Substances (RoHS) Directive	22
2.15 Corrosive environment	22
3.0 Configuring and mounting the drive	23
3.1 Handling and static-discharge precautions	23
3.2 Configuring the drive	24
3.3 Serial ATA cables and connectors	24
3.4 Drive mounting	25
4.0 Serial ATA (SATA) interface	27
4.1 Hot-Plug compatibility	27
4.2 Serial ATA device plug connector pin definitions	28
4.3 Supported ATA commands	29
4.3.1 Identify Device command	31
4.3.2 Set Features command	35
4.3.3 S.M.A.R.T. commands	36
5.0 Seagate Technology support services	37
Index	39
A	39
B	39
C	39
D	39
E	39
F	39
G	39
H	39
I	39
K	40
L	40
M	40
N	40
O	40
P	40
Q	40
R	40
S	40
T	41
U	41
V	41