Sharp ER-A330 Programmer Manual - Page 9
Mrs = Standard Key Layout - manuals
View all Sharp ER-A330 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
[JOB#916] MRS = 0000 #916-A, B: Not used (Fixed at "00") #916-C: 1. Negative merchandise subtotal 2. Subtotal entry compulsory before tendering 3. Subtotal entry before direct non-tendering finalization 1. Negative merchandise subtotal Allow Disallow 2. Subtotal entry compulsory before tendering Non-compulsory Compulsory Non-compulsory Compulsory 3 .Subtotal entry before direct non-tendering finalization Non-compulsory Compulsory Non-compulsory Compulsory Non-compulsory Compulsory Non-compulsory Compulsory 916-C 0 5 1 2 3 4 5 6 7 #916-D: 1. Coupon PLU printing on X/Z report 2. Net sales subtotal (NET1) printing on X/Z report 3. CHECK change total printing on X/Z report 1. Print coupon 2. Print net 3. Print CHK PLU's on sales SBTL CHANGE on general report (NET1) on general report general report 916-D Print Print Skip Print Skip Print Skip 0 5 1 2 3 Print Print 4 Skip Skip 5 Print 6 Skip Skip 7 [JOB#917] NOT USED MRS = 0000 2. Limit on the least sighificant digit in entering the amount on item 1. Difference memory No Yes 2. Limit on the least sighificant digit in entering the amount on item Arbitary 0 only 0 and 5 only Arbitary 0 only 0 and 5 only 927-C 05 1 2 4 5 6 #927-D: 1. Application of rounding 2. Limit on the least significant digit in entering the amount of payment 1. Application of rounding Item & Payment Payment 2. Limit on the least significant digit in entering the amount of payment Arbitary 0 only 0 and 5 only Arbitary 0 only 0 and 5 only 927-D 05 1 2 4 5 6 [JOB#930∼931] MRS = 0000 RESET REPORT COUNTER "0000" Job# X ABCD TL/NS Initial value of Z countr JOB # 930 931 Z1 report counter Z2 report counter Function [JOB#918] MRS = 0000 #918-A: 1. Dirrect non-tendering finalization after previous tender entry 1. Dirrect non-tendering finalization after previous tender entry Disable Enable 918-A 0 2 5 #918-B, C, D: Not used (Fixed at "000") [JOB#919] MRS = 0000 #919-A, B, C: Not used (Fixed at "000") 919-D: 1. Foreign currency format [JOB#942, 943, 969] MRS = 0000000000000 GT COUNTER PRESETTING 0 Job# X 0000000000000 TL/NS 13 digits JOB # 942 943 969 GT2 (Positive GT) GT3 (Negative GT) TRAINING GT Function Note: GT1 is obtained by the following calculation. Equation: GT1=GT2-GT3 1. Foreign currency Not Omit digits lower than TAB position 919-D 0 5 1 [JOB#950] MRS = STANDARD KEY LAYOUT Free key layout (Except for department keys and direct PLU keys.) Initial setting [JOB#927] MRS = 0000 Key number manual increment #927-A: 1. Rounding up of the units digit of amount Key number automatic increment #927-B: 1. Rounding down of the units digit of amount 1. Rounding the units digit of amount Common destination Netherland/Switzerland Norway 927-AB 00 5 82 54 950 X XXX Free key TL/NS Key No. X To inhibit SBTL #927-C: 1. Difference memory (Difference between before-round- To skip ing and after-rounding) XXX: Key No. = 17 ∼ 150 - 8 -