Sharp LC46D43U Service Manual - Page 100

Outline And Adjustment - tv lc 46d43u

Get Sharp LC46D43U - Aquos - 720p LCD HDTV PDF manuals and user guides
UPC - 890552648849
View all Sharp LC46D43U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

LC-46D43U LOCU-46TDL43IUNE AND ADJUSTMENT Service Manual [1] Outline In this Service Manual, only parts in the LCD module are shown. For the other points, refer to the LC-46D43U (S47D9LC46D43U) Service Manual. [2] Adjustment When replacing the LCD control PCB, follow these steps to adjust VCOM. 1) Remove the wire from the LCD control PCB CN3. 2) Connect a wire of the VCOM adjustment jig (electronic volume adjustment BOX) to CN3 (see Fig. 1). 3) Turn on the TV set. 4) Turn on the jig (connect to the AC). 5) Enter the process mode to display the item "LCD TEST PATTERN OFF" (see Fig. 2). 6) Press the volume up key once to display a flicker pattern. 7) Press the jig's UP/DOWN switch while looking at the screen to adjust the point so that the flicker is minimized (see Fig. 3). 8) After completing adjustment, press the WRITE switch and make sure the lamp of the WRITE button goes out. (Writing is complete when the lamp goes out.) 9) Turn off the jig (turn the AC off). 10)Turn off the TV set. 11)Remove the jig's wire connected to CN3. 12)Reconnect the wire of the set to CN3. Jig connection Fig. 1 Jig connecting location Fig. 2 Test pattern selection screen Fig. 3 VCOM adjustment jig (RUNTZA059WJZZ) i

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
LC-46D43U
i
LC-46D43U
Service Manual
OUTLINE AND ADJUSTMENT
[1] Outline
In this Service Manual, only parts in the LCD module are shown. For the other points, refer to the LC-46D43U (S47D9LC46D43U) Service Manual.
[2] Adjustment
When replacing the LCD control PCB, follow these steps to adjust VCOM.
1)
Remove the wire from the LCD control PCB CN3.
2)
Connect a wire of the VCOM adjustment jig (electronic volume adjustment BOX) to CN3 (see Fig. 1).
3)
Turn on the TV set.
4)
Turn on the jig (connect to the AC).
5)
Enter the process mode to display the item “LCD TEST PATTERN OFF” (see Fig. 2).
6)
Press the volume up key once to display a flicker pattern.
7)
Press the jig's UP/DOWN switch while looking at the screen to adjust the point so that the flicker is minimized (see Fig. 3).
8)
After completing adjustment, press the WRITE switch and make sure the lamp of the WRITE button goes out. (Writing is complete when the lamp
goes out.)
9)
Turn off the jig (turn the AC off).
10)Turn off the TV set.
11)Remove the jig’s wire connected to CN3.
12)Reconnect the wire of the set to CN3.
Fig. 1 Jig connecting location
Fig. 2 Test pattern selection screen
Fig. 3 VCOM adjustment jig (RUNTZA059WJZZ)
Jig connection