Sharp PG-C45XL PG-C45X Operation Manual - Page 38

Image Projection, Basic Procedure

Get Sharp PG-C45XL PDF manuals and user guides View all Sharp PG-C45XL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Image Projection Basic Procedure Connect the required external equipment to the projector before operating the following procedures. Info • The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language according to the procedure on page 36. Power indicator Lamp replacement indicator 1 Plug the power cord into the wall outlet. • The power indicator illuminates red, and the projector enters standby mode. 2 ON Press on the projector or on the remote control. • The power indicator illuminates green. After the lamp replacement indicator illuminates, the projector is ready to start operation. Power (ON) button Power (OFF) button ENTER button Note • The lamp replacement indicator illuminates, indicating the status of the lamp. Green: The lamp is ready. Green blinking: The lamp is warming up. Red: The lamp should be replaced. • If the power is turned off and immediately switched on again, the lamp replacement indicator may take time to illuminate. • When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands. When"Anti-Theft"(seepage 75)isset, the keycode input box will appear. • Enter the keycode. Power (OFF) button ENTER button Note • When entering the keycode, press the buttons previously set on the projector or the remote control. Info • When "Anti-Theft" is set, enter the keycode or the input display will not appear. Even when the signal is input, the display will not appear. (see page 75.) -34 MKeycode input box INPUT button ',", \, | buttons MENU button Power (ON) button MENU button ', ", \, | buttons INPUT buttons

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Image Projection
▼
Keycode input box
-34
Lamp
replacement
indicator
Power
indicator
INPUT
button
'
,
"
,
\
,
|
buttons
MENU
button
ENTER
button
Power (ON)
button
INPUT
buttons
'
,
"
,
\
,
|
buttons
MENU button
ENTER
button
Power (OFF)
button
Basic Procedure
Connect the required external equipment to the pro-
jector before operating the following procedures.
Info
•
The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page
36
.
1
Plug the power cord into the
wall outlet.
•
The power indicator illuminates red, and
the projector enters standby mode.
2
Press
ON
on the projector or on
the remote control.
•
The power indicator illuminates green.
After the lamp replacement indicator il-
luminates, the projector is ready to start
operation.
Note
•
The lamp replacement indicator il-
luminates, indicating the status of the
lamp.
Green:
The lamp is ready.
Green blinking:
The lamp is
warming up.
Red:
The lamp should be replaced.
•
If the power is turned off and immediately
switched on again, the lamp replacement
indicator may take time to illuminate.
•
When controlling the projector using
RS-232C commands from a com-
puter, wait for at least 30 seconds
after the power has been turned on,
and then transmit the commands.
When“Anti-Theft”(see page
75
) is set,
the keycode input box will appear.
•
Enter the keycode.
Note
•
When entering the keycode, press
the buttons previously set on the
projector or the remote control.
Info
•
When “Anti-Theft” is set, enter the
keycode or the input display will not ap-
pear. Even when the signal is input, the
display will not appear. (see page
75
.)
Power (ON)
button
Power (OFF)
button