Sharp PN-L401C PN-L401C Quick Start Setup Guide - Page 6
Emounting Precautions
View all Sharp PN-L401C manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
MOUNTING PRECAUTIONS • This product is for use indoors. • When using a commercially available stand or mounting bracket, use a stand or mounting bracket that comply with VESA specifications. • Since the monitor is heavy, consult your dealer before installing, removing or moving the monitor. • Mounting the monitor on the wall requires special expertise and the work must be performed by an authorized SHARP dealer. You should never attempt to perform any of this work yourself. Our company will bear no responsibility for accidents or injuries caused by improper mounting or mishandling. • Use the monitor with the surface perpendicular to a level surface. If necessary, the monitor may be tilted up to 20 degrees upward. • When moving the monitor, be sure to hold it around the periphery. Do not grasp the screen or tray. This may cause product damage, failure, or injury. • This monitor should be used at an ambient temperature between 41°F (5°C) and 95°F (35°C). Provide enough space around the monitor to prevent heat from accumulating inside. For the monitor in landscape orientation Unit: inch [mm] 7-7/8 [200] • Adhere to the following when installing the monitor in its portrait orientation. Failing to adhere to the following may cause malfunctions. - Install the monitor such that the power LED is located on the bottom side. - Set the PORTRAIT/LANDSCAPE INSTALL on the MONITOR menu to PORTRAIT. (See OPERATION MANUAL.) - Be sure to clamp the power cord (supplied) by using the supplied cable clamp (affixing type). When clamping the power cord, take care not to stress the terminal of the power cord. Do not bend the power cord excessively. • Use the supplied vertical sticker when you install the monitor in portrait orientation. 2 2 [50] [50] 2 [50] 5/16 [7] For the monitor in portrait orientation Unit: inch [mm] 7-7/8 [200] 5/16 [7] 2 2 [50] [50] Power LED 2 [50] • If it is difficult to provide sufficient space for any reason such as the installation of the monitor inside a housing, or if the ambient temperature may be outside of the range of 41°F (5°C) to 95°F (35°C), install a fan or take other measures to keep the ambient temperature within the required range. • When installing two or more monitor units side-by-side, provide space of at least 3/16 inch (5 mm) around them to prevent stress on the adjacent unit or structure due to thermal expansion. • Do not block any ventilation openings. If the temperature inside the monitor rises, this could lead to a malfunction. • Do not place the monitor on a device which generates heat. Operation panel Flat installation • When using the monitor laying flat on a surface (when the monitor is tilted 20 degrees or more upward from the perpendicular in relation to a level surface), consult an authorized SHARP dealer because there are some specific mounting conditions. Adhere to the following. Failing to adhere to the following may cause malfunctions. - Set HORIZONTAL INSTALLATION in the MONITOR menu to UPWARD. (See OPERATION MANUAL.) - Use the monitor at the ambient temperature within the range of 41°F (5°C) to 86°F (30°C). Provide 7-7/8 inch (200 mm) or more space between the monitor and the floor or other mounting surfaces and surrounding objects to prevent heat from accumulating inside. If it is difficult to provide sufficient space or if the ambient temperature may be outside of the range of 41°F (5°C) to 86°F (30°C), install a fan or take other measures to keep the ambient temperature within the required range. - Do not press hard on the LCD panel or otherwise subject it to impacts. Flat installation (UPWARD) 7-7/8 [200] 7-7/8 [200] Unit: inch [mm] 7-7/8 [200] 7-7/8 [200] 7-7/8 [200] E4