Sony HCD-MDX10 Service Manual - Page 11

Checks Prior To Parts Replacement And Adjustments, Forced Reset, Ad Error : Below 2

Get Sony HCD-MDX10 - Compact Disk Deck Receiver Component PDF manuals and user guides View all Sony HCD-MDX10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTS Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent. Details of the procedures are described in "5 Electrical Adjustments". Laser power check (7-6-2 : See page 29) Traverse check (7-6-3 : See page 29) Focus bias check (7-6-4 : See page 30) C PLAY check (7-6-5 : See page 30) Self-recording/playback check (REC/PLAY) (7-6-6 : See page 30) TEMP check (Temperature compensation offset check) (7-6-1 : See page 29) Criteria for Determination (Unsatisfactory if specified value is not satisfied) Measure if unsatisfactory: • 0.9 mW power Specified value : 0.84 to 0.92 mW • 7.0 mW power Specified value : 6.8 to 7.2 mW lop (at 7mW) • Labeled on the optical pickup Iop value ± 10mA • Traverse waveform Specified value : Below 10% offset • Error rate check Specified value : For points a, b, and c C1 error : Below 220 AD error : Below 2 • Error rate check Specified value: a.When using test disc (MDW-74/AU-1) C1 error : Below 80 AD error : Below 2 b.When using check disc (TDYS-1) C1 error : Below 50 • CPLAY error rate check Specified value: C1 error : Below 80 AD error : Below 2 • Unsatisfactory if displayed as T=@@ (##) NG" NG (@@, ## are both arbitrary numbers) • Clean the optical pick-up • Adjust again • Replace the optical pick-up • Replace the optical pick-up • Replace the optical pick-up • Replace the optical pick-up • Replace the optical pick-up If always unsatisfactory: • Replace the overwrite head • Check for disconnection of the circuits around the overwrite head If occasionally unsatisfactory: • Check if the overwrite head is distorted • Check the mechanism around the sled • Check for disconnection of the circuits around D101 (BD board) • Check the signals around IC101, IC121, CN102, CN103 (BD board) Note: The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for adjustments. When performing adjustments, use the specified values for adjustments. FORCED RESET The system microprocessor can be reset in the following procedure. Use these procedure when the unit cannot be operated normally due to the overrunning of the microprocessor, etc. Procedure : Disconnect the power plug, short-circuit both edge of BT921. [MAIN BOARD] (Component Side) IC801 BT921 - 11 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
– 11 –
•
0.9 mW power
Specified value : 0.84 to 0.92 mW
•
7.0 mW power
Specified value : 6.8 to 7.2 mW
lop (at 7mW)
•
Labeled on the optical pickup
Iop value ± 10mA
•
Traverse waveform
Specified value : Below 10% offset
•
Error rate check
Specified value : For points a, b, and c
C1 error : Below 220
AD error : Below 2
•
Error rate check
Specified value:
a.When using test disc (MDW-74/AU-1)
C1 error : Below 80
AD error : Below 2
b.When using check disc (TDYS-1)
C1 error : Below 50
•
CPLAY error rate check
Specified value:
C1 error : Below 80
AD error : Below 2
•
Unsatisfactory if displayed as T=@@ (##) NG”
NG
(@@, ## are both arbitrary numbers)
CHECKS PRIOR TO PARTS REPLACEMENT AND ADJUSTMENTS
Before performing repairs, perform the following checks to determine the faulty locations up to a certain extent.
Details of the procedures are described in “5 Electrical Adjustments”.
Laser power check
(7-6-2 : See page 29)
Traverse check
(7-6-3 : See page 29)
Focus bias check
(7-6-4 : See page 30)
C PLAY check
(7-6-5 : See page 30)
Self-recording/playback
check
(REC/PLAY)
(7-6-6 : See page 30)
TEMP check
(Temperature
compensation
offset check)
(7-6-1 : See page 29)
Criteria for Determination
(Unsatisfactory if specified value is not satisfied)
•
Clean the optical pick-up
•
Adjust again
•
Replace the optical pick-up
•
Replace the optical pick-up
•
Replace the optical pick-up
•
Replace the optical pick-up
•
Replace the optical pick-up
If always unsatisfactory:
•
Replace the overwrite head
•
Check for disconnection of the circuits around the
overwrite head
If occasionally unsatisfactory:
•
Check if the overwrite head is distorted
•
Check the mechanism around the sled
•
Check for disconnection of the circuits around D101
(BD board)
• Check the signals around IC101, IC121, CN102,
CN103 (BD board)
Measure if unsatisfactory:
Note:
The criteria for determination above is intended merely to determine if satisfactory or not, and does not serve as the specified value for
adjustments.
When performing adjustments, use the specified values for adjustments.
FORCED RESET
The system microprocessor can be reset in the following procedure.
Use these procedure when the unit cannot be operated normally due to the overrunning of the microprocessor, etc.
Procedure :
Disconnect the power plug, short-circuit both edge of BT921.
[MAIN BOARD] (Component Side)
IC801
BT921