Sony HT-9900M HT5950DP Instructions (entire HT system) - Page 55

Specifications - rating

Page 55 highlights

Additional Information Error messages If there is a malfunction, the display shows a message. You can check the condition of the receiver by the message. Refer to the following table to solve the problem. DEC. EROR Appears when the signal which the receiver cannot decode (ex. DTS-CD) is input when "DEC. XXXX" in the CUSTOMIZE menu is set to "DEC. PCM". Set to "DEC. AUTO". PROTECT Irregular current is output from the speakers. The receiver will automatically turn off after a few seconds. Check the speaker connection and turn on the power again. If this problem persists, consult your nearest Sony dealer. If you are unable to remedy the problem using the troubleshooting guide Clearing the receiver's memory may remedy the problem (page 18). However, note that all memorized settings will be reset to their factory settings and you will have to readjust all settings on the receiver. If the problem persist Consult your nearest Sony dealer. Reference sections for clearing the receiver's memory To clear All memorized settings Customized sound fields See page 18 page 37 Specifications AUDIO POWER SPECIFICATIONS POWER OUTPUT AND TOTAL HARMONIC DISTORTION: (Model of area code U only) With 6 ohm loads, both channels driven, from 120 - 20,000 Hz; rated 90 watts (STR-K9900P)/ 70 watts (STR-K5900P) per channel minimum RMS power, with no more than 0.7% total harmonic distortion from 250 milliwatts to rated output. Amplifier section Power Output1) Model of area code U (6 ohms 1 kHz, THD 10%) STR-K9900P: FRONT2): 140 W/ch CENTER2): 140 W SURR2): 140 W/ch SURR BACK2): 140 W STR-K5900P: FRONT2): 110 W/ch CENTER2): 110 W SURR2): 110 W/ch SURR BACK2): 110 W Model of area code CA (6 ohms 1 kHz, THD 0.7%) STR-K9900P: FRONT2): 90 W/ch CENTER2): 90 W SURR2): 90 W/ch SURR BACK2): 90 W STR-K5900P: FRONT2): 70 W/ch CENTER2): 70 W SURR2): 70 W/ch SURR BACK2): 70 W (6 ohms 1 kHz, THD 10%) STR-K9900P: FRONT2): 140 W/ch CENTER2): 140 W SURR2): 140 W/ch SURR BACK2): 140 W STR-K5900P: FRONT2): 110 W/ch CENTER2): 110 W SURR2): 110 W/ch SURR BACK2): 110 W continued 55US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60

Additional Information
55
US
Error messages
If there is a malfunction, the display shows a
message. You can check the condition of the
receiver by the message. Refer to the following
table to solve the problem.
DEC. EROR
Appears when the signal which the receiver cannot
decode (ex. DTS-CD) is input when “DEC. XXXX”
in the CUSTOMIZE menu is set to “DEC. PCM”.
Set to “DEC. AUTO”.
PROTECT
Irregular current is output from the speakers. The
receiver will automatically turn off after a few
seconds. Check the speaker connection and turn on
the power again. If this problem persists, consult
your nearest Sony dealer.
If you are unable to remedy the
problem using the
troubleshooting guide
Clearing the receiver’s memory may remedy the
problem (page 18). However, note that all
memorized settings will be reset to their factory
settings and you will have to readjust all settings
on the receiver.
If the problem persist
Consult your nearest Sony dealer.
Reference sections for clearing
the receiver’s memory
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(Model of area code U only)
With 6 ohm loads, both channels driven, from
120 – 20,000 Hz; rated 90 watts (STR-K9900P)/
70 watts (STR-K5900P) per channel minimum
RMS power, with no more than 0.7% total
harmonic distortion from 250 milliwatts to rated
output.
Amplifier section
Power Output
1)
Model of area code U
(6 ohms 1 kHz, THD 10%)
STR-K9900P:
FRONT
2)
: 140 W/ch
CENTER
2)
: 140 W
SURR
2)
: 140 W/ch
SURR BACK
2)
: 140 W
STR-K5900P:
FRONT
2)
: 110 W/ch
CENTER
2)
: 110 W
SURR
2)
: 110 W/ch
SURR BACK
2)
: 110 W
Model of area code CA
(6 ohms 1 kHz, THD 0.7%)
STR-K9900P:
FRONT
2)
: 90 W/ch
CENTER
2)
: 90 W
SURR
2)
: 90 W/ch
SURR BACK
2)
: 90 W
STR-K5900P:
FRONT
2)
: 70 W/ch
CENTER
2)
: 70 W
SURR
2)
: 70 W/ch
SURR BACK
2)
: 70 W
(6 ohms 1 kHz, THD 10%)
STR-K9900P:
FRONT
2)
: 140 W/ch
CENTER
2)
: 140 W
SURR
2)
: 140 W/ch
SURR BACK
2)
: 140 W
STR-K5900P:
FRONT
2)
: 110 W/ch
CENTER
2)
: 110 W
SURR
2)
: 110 W/ch
SURR BACK
2)
: 110 W
To clear
See
All memorized settings
page 18
Customized sound fields
page 37
Specifications
continued