Sony MHC-GX25 Operating Instructions - Page 14

Listening to the radio, — Preset Tuning, Listening to a preset station

Page 14 highlights

Other Operations To Tune in a station with a weak signal Set another station to the existing preset number Do this Follow the procedure described in "Manual tuning preset" (page 13). Start over from step 1. After step 3, press PRESET -/+ (or . or > on the unit) repeatedly to select the preset number you want to store the other station. To change the AM tuning interval (except for European, Russian, Middle Eastern and Philippine models) The AM tuning interval is factory-preset to 9 kHz (or 10 kHz for some areas). To change the AM tuning interval, tune in any AM station first, then turn off the system. While holding TUNER/ BAND on the unit, press ?/1 on the unit. When you change the interval, all the AM preset stations are erased. To reset the interval, repeat the same procedure. Note You cannot change the AM tuning interval in the Power Saving Mode. Tips • The preset stations are retained for about a day even if you disconnect the power cord or if a power failure occurs. • To improve the reception, adjust the supplied antennas or connect an external antenna. Listening to the radio You can listen to a radio station either by selecting a preset station, or by manually tuning in the station. Listening to a preset station - Preset Tuning Preset radio stations in the tuner's memory first (see "Presetting radio stations" on page 13). 1 Press TUNER/BAND repeatedly to select "FM" or "AM". 2 Press PRESET -/+ (or . or > on the unit) repeatedly to select the desired preset station. Preset number Frequency 14GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40

14
GB
Other Operations
To change the AM tuning interval
(except for European, Russian,
Middle Eastern and Philippine
models)
The AM tuning interval is factory-preset to
9
kHz (or 10
kHz for some areas). To change the
AM tuning interval, tune in any AM station first,
then turn off the system. While holding TUNER/
BAND on the unit, press
?/1
on the unit. When
you change the interval, all the AM preset
stations are erased. To reset the interval, repeat
the same procedure.
Note
You cannot change the AM tuning interval in the
Power Saving Mode.
Tips
The preset stations are retained for about a day even
if you disconnect the power cord or if a power failure
occurs.
To improve the reception, adjust the supplied
antennas or connect an external antenna.
You can listen to a radio station either by
selecting a preset station, or by manually tuning
in the station.
Listening to a preset station
— Preset Tuning
Preset radio stations in the tuner’s memory first
(see “Presetting radio stations” on page 13).
1
Press TUNER/BAND repeatedly to
select “FM” or “AM”.
2
Press PRESET –/+ (or
.
or
>
on
the unit) repeatedly to select the
desired preset station.
To
Do this
Tune in a station
with a weak signal
Follow the procedure described
in “Manual tuning preset”
(page 13).
Set another station
to the existing
preset number
Start over from step 1. After
step 3, press PRESET –/+ (or
.
or
>
on the unit)
repeatedly to select the preset
number you want to store the
other station.
Listening to the radio
Frequency
Preset number