Sub-Zero 601F 600 Series & 430 Panel Specifications

Dimensions in

parentheses are in

millimeters unless

otherwise specified.

BUILT-IN REFRIGERATION

18

ANTI-TIP BLOCKING KIT

To prevent the unit from tipping forward and to

provide a stable installation, the unit must be

secured in place with an anti-tip blocking kit. If

there is a solid soffit above the unit with clear-

ance between the unit and the soffit of 1" (25)

or less, you won‘t need to block the unit. But for

installations with clearances of more than 1"

(25), you must block the unit with the anti-tip

blocking kit (wood block and hardware) provided

with each Sub-Zero Built-In model. Refer to the

Built-In Installation Instructions packed with the

appliance, which provides step-by-step proce-

dures for making sure the unit is installed

properly.

ADDING

PANELS

In your plan for panels, be sure you are working

with the Sub-Zero panel design family called for

in your design. If you have chosen the stainless

steel design, the unit will be shipped complete

with wrapped stainless steel doors and handle

hardware. You will not have to install door

panels.

Specifications on the following pages provide

panel dimensions and installation considerations

for framed and overlay door panels.

Side panels can be used with the framed,

overlay and stainless steel design applications.

Refer to specifications on page 26.

FRAMED

DOOR

PANELS

If you and your client have ordered a framed

design model, you will be adding panels to give

the unit the custom Sub-Zero look. The framed

panel design option is available on all Built-In

units except Models 648PRO and 648PROG. For

exact door panel dimensions for Built-In framed

models, refer to the Framed Panel Specifications

on pages 20–21. Also refer to the full-scale

illustrations at the end of this section for panel

and handle considerations.

The traditional framed models come with an

elegant, smooth, full-length handle. Optional

extended full-length handles that provide

additional finger clearance for raised panels are

available through your Sub-Zero dealer.

If the thickness of the custom panels is less

than

1

/

4

" (6), they must be backed up with a

sheet of shim material to build the total thick-

ness to

1

/

4

" (6). If the panel is thicker than

1

/

4

"

(6), an edge must be routed around the panel to

ensure a proper fit. Refer to illustrations 1 and 2.

IMPORTANT NOTE:

On all framed models,

routing, recessing or optional extended handles

may be required on raised panels for finger clear-

ance under the handle. Refer to the full-scale

illustrations at the end of this section.

For glass door Models 601RG, 611G and 650G,

the refrigerator door panel must include a cut-

out to accommodate the window. Refer to the

Framed Panel Specifications on pages 20–21.

IMPORTANT NOTE:

On glass door models, the

glass portion of the door must be exposed and

not covered by any part of the panel.

For Models 685 and 695, the refrigerator door

panel must include a cut-out to accommodate

the glasswell and bezel. The thickness of the

panel in this area can range from

1

/

4

" (6) to a

maximum of 1

1

/

8

" (29). If the panel is thicker,

provisions must be made to rout out a space to

accommodate the decorative bezel surrounding

the glasswell.

PANELS THICKER THAN

1

/

4

"

(6)

Trim reveal

1

/

4

"

(6)

min

Rout to

1

/

4

"

(6)

thickness

PANELS

1

/

4

"

(6) THICK OR LESS

1

/

4

"

(6)

Panel

Trim reveal

1

/

4

"

(6)

min

Illus. 2

Illus. 1

ACCESSORIES

Optional accessories

are available

through your

Sub-Zero dealer. To

obtain local dealer

information, visit the

Showroom Locator

section of our

website,

subzero.com.

Sub-Zero 601F 600 Series & 430 Panel Specifications

Sub-Zero 601F Manual

Sub-Zero 601F manual content summary: