TP-Link TL-SG3109 User Guide

TP-Link TL-SG3109 - Switch Manual

Get TP-Link TL-SG3109 - Switch PDF manuals and user guides
UPC - 845973020484
View all TP-Link TL-SG3109 manuals
Add to My Manuals
Save this manual to your list of manuals

TP-Link TL-SG3109 manual content summary:

  • TP-Link TL-SG3109 | User Guide - Page 1
    Embedded Web System User Guide TL-SG3109 9-port Gigabit Managed Switch TL-SL3428 24+4G Gigabit Managed Switch TL-SL3452 48+4G Gigabit Managed Switch Rev: 1.0
  • TP-Link TL-SG3109 | User Guide - Page 2
    adaptation without permission from TP-LINK Technologies Co., Ltd. Copyright © 2006 TP-LINK Technologies Co., Ltd. and used in accordance with the instructions, may cause harmful interference to radio by turning the equipment off and on, the user is encouraged to try to correct the interference by
  • TP-Link TL-SG3109 | User Guide - Page 3
    TABLE OF CONTENTS Preface ...1 Guide Overview...1 Intended Audience...2 Section 1. Getting Started 3 1.1 Configuring the device to use TP-Link Embedded Web Interface 3 1.2 Starting the TP-Link Embedded Web Interface 3 1.3 Understanding the TP-Link Embedded Web Interface 4 1.3.1 Device
  • TP-Link TL-SG3109 | User Guide - Page 4
    Authentication Profiles 24 5.1.1.4 Mapping Authentication 30 5.1.2.1 Defining Local Users...30 5.1.2.2 Defining Line Port Security 36 5.2.3.2 Enabling Storm Control 37 Section 6. Defining IP Addresses 39 6.1 Defining IP Addressing...39 6.1.1 Defining IP Addresses...39 6.1.2 Defining the Default
  • TP-Link TL-SG3109 | User Guide - Page 5
    Section 7. Configuring Interfaces 45 7.1 Configuring Ports...45 7.2 Configuring LAGs...47 7.2.1 Defining LAG Members...47 7.2.2 Configuring LACP...48 7.3 Configuring VLANs...49 7.3.1 Defining VLAN Properties 49 7.3.2 Defining VLAN Membership 50 7.3.3 Defining VLAN Interface
  • TP-Link TL-SG3109 | User Guide - Page 6
    .2.1 Enabling Quality of Service 82 12.2.2 Defining Queues...83 12.3 Mapping Queues...84 12.3.1 Mapping CoS Values to Queues 84 12.3.2 Mapping QoS Values to Queues 84 Section 13. Managing System Files 86 13.1 Downloading System Files 86 13.1.1 Download Type...86 13.1.2 Firmware Download...87 13
  • TP-Link TL-SG3109 | User Guide - Page 7
    13.4 Copying System Files...88 Section 14. Performing Device Diagnostics 90 14.1 Configuring Port Mirroring 90 14.2 Viewing Integrated Cable Tests 91 14.3 Viewing Optical Transceivers 92 Section 15. Viewing Statistics 93 15.1 Viewing Interface Statistics 93 15.1.1 Viewing
  • TP-Link TL-SG3109 | User Guide - Page 8
    monitor network performance. This preface provides an overview to the TP-Link Embedded Interface User Guide. This preface includes the following sections:  Guide Overview  Intended Audience Guide Overview This user guide is divided into the following sections to provide concise information for
  • TP-Link TL-SG3109 | User Guide - Page 9
    Section 14. Performing Device Diagnostics - Provides information about port mirroring configuration, copper and fiber cables testing, and Network (RMON) statistics, and device history events. Intended Audience This guide is intended for network administrators familiar with IT concepts and network
  • TP-Link TL-SG3109 | User Guide - Page 10
    Web Interface can not be accessed until the device is properly configured. To use TP-Link Embedded Web Interface, use the console interface to assign an IP address and subnet mask on the default VLAN, and add a super-user with the highest privilege level (15) which is allowed to log onto the device
  • TP-Link TL-SG3109 | User Guide - Page 11
    the CLI to define default passwords, see the TP-Link CLI Reference Guide. 5. Click . The TP-Link Embedded Web Interface Home Page opens: Figure 2: TP-Link Embedded Web Interface Home Page The TP-Link Embedded Web Interface Home Page contains the following views:  Port LED Indicators - Located
  • TP-Link TL-SG3109 | User Guide - Page 12
    TP-Link user interface buttons, including both management buttons and task icons.  Using the TP-Link Embedded Web Interface Management Buttons - Provides instructions this guide are based on the TL-SL3428 device. The figures captions may differ if another device is used. 1.3.2 Using the TP-Link
  • TP-Link TL-SG3109 | User Guide - Page 13
    Configuration Information User-defined information can be added to specific TP-Link Web Interface pages, by opening a new Add page. To add information to tables or TP-Link Web Interface pages: 1. Open an TP-Link Web Interface page. 2. Click . An Add page opens, for example Add IP Interface Page
  • TP-Link TL-SG3109 | User Guide - Page 14
    file to the startup configuration file before resetting the device. For instructions, see Managing System Files "Copying System Files" on page 171. To reset the device: 1. Click System > General > Reset. The Reset Page opens. Figure 7: Reset Page 2. Click . A confirmation message is displayed
  • TP-Link TL-SG3109 | User Guide - Page 15
    System Object ID, System Up Time, System IP and MAC addresses, and both software and and name.  System Name - Defines the user-defined device name. The field range is 0-160 - Displays the amount of time since the most recent device reset. The system time is displayed in the following format: Days
  • TP-Link TL-SG3109 | User Guide - Page 16
    Section 3. Setting the System Time This section provides information for configuring system time parameters, including:  Configuring Daylight Savings Time  Configuring SNTP 3.1 Configuring Daylight Savings Time The System Information Time Page contains fields for defining system time parameters
  • TP-Link TL-SG3109 | User Guide - Page 17
     Latvia - From the last weekend of March until the last weekend of October.  Lebanon - From the last weekend of March until the last weekend of October.  Lithuania - From the last weekend of March until the last weekend of October.  Luxembourg - From the last weekend of March until the last
  • TP-Link TL-SG3109 | User Guide - Page 18
    amount of time for DST (in minutes). The default time is 60 minutes.  From - Indicates example: 05:30. Recurring:  Recurring - Enables user-defined DST for countries in which DST is constant from fields. 3. To configure the device to automatically switch to DST, select Daylight Savings and select
  • TP-Link TL-SG3109 | User Guide - Page 19
    The device supports the Simple SNTP client, and cannot provide time services to other systems. The device can Stratum 2 server receives the time over a network link, via NTP, from a Stratum 1 server. Information information is used when the SNTP server IP address is unknown. The first Anycast
  • TP-Link TL-SG3109 | User Guide - Page 20
    fields:  Poll Interval - Defines the interval (in seconds) at which the SNTP server is polled for Unicast information. The Poll Interval default is 1024 seconds.  Enable Receive Broadcast Servers Updates - Defines whether or not the device monitors the SNTP servers for Broadcast server time
  • TP-Link TL-SG3109 | User Guide - Page 21
    . The possible field values are: - Checked - Removes the selected Encryption Key ID. - Unchecked - Maintains the Encryption Key IDs. This is the default value. 2. Check the Enable SNTP Authentication checkbox. 3. Click . SNTP Authentication is defined, and the device is updated. To define SNTP
  • TP-Link TL-SG3109 | User Guide - Page 22
    Page contains the following fields:  SNTP Server - Displays user-defined SNTP server IP addresses. Up to eight SNTP servers can be defined. Removes the SNTP server. - Unchecked - Maintains the SNTP server. This is the default value. 2. Click . The Add SNTP Server Page opens: Figure 16: Add SNTP
  • TP-Link TL-SG3109 | User Guide - Page 23
    Page contains the following fields:  Interface - Indicates the interface on which SNTP can be enabled. The possible field values are: - Port - Indicates the specific port number on which SNTP is enabled. - LAG - Indicates the specific LAG number on which SNTP is enabled. - VLAN - Indicates the
  • TP-Link TL-SG3109 | User Guide - Page 24
    notice has occurred. Provides device information. Provides detailed information about the log. If a Debug error occurs, contact Customer Tech Support. This section contains the following topics:  Defining General Log Properties  Viewing Memory Logs  Viewing Flash Logs  Defining System Log
  • TP-Link TL-SG3109 | User Guide - Page 25
    the following fields:  Enable Logging - Indicates if device global logs for Cache, File, and Server Logs are enabled. Console logs are enabled by default. The possible field values are: - Checked - Enables device logs. - Unchecked - Disables device logs.  Severity - - Notice - Provides device
  • TP-Link TL-SG3109 | User Guide - Page 26
    .  UDP Port - Defines the UDP port to which the server logs are sent. The possible range is 1 - 65535. The default value is 514.  Port-Facility - Defines server. The field default is Local 7. The possible field values are Local 0 - Local 7.  Description - Provides a user-defined server description
  • TP-Link TL-SG3109 | User Guide - Page 27
    Figure 23: Add Syslog Server Page 3. Define the IP Address, UDP Port, Facility, Description, and Minimum Severity fields. 4. Click . The Log server is defined and the device is updated. 20
  • TP-Link TL-SG3109 | User Guide - Page 28
    ports, device management methods, users, and server security for the TP-Link user groups. User groups are defined for interfaces according to IP addresses or IP user groups. For example, User Group 1 can access the switch module only via an HTTPS session, while User Group 2 can access the switch
  • TP-Link TL-SG3109 | User Guide - Page 29
    default port on which the access profile is defined. - LAG - Specifies the LAG on which the access profile is defined. - VLAN - Specifies the VLAN on which the access profile is defined. - Source IP Address - Defines the interface source IP address to which the access profile applies. The Source IP
  • TP-Link TL-SG3109 | User Guide - Page 30
    default. 3. Click . The access profile is saved and the device is updated. 5.1.1.2 Defining Profile Rules Access profiles can contain up to 128 rules that determine which users can manage the switch module, and by which methods. Users are: - Port - Attaches the rule to the selected port. - LAG
  • TP-Link TL-SG3109 | User Guide - Page 31
    IP address.  Action - Defines the action attached to the rule. The possible field values are: - Permit - Permits access to the device. - Deny - Denies access to the device. This is the default RADIUS server is not available, then the user is authenticated locally. To define Authentication profiles 24
  • TP-Link TL-SG3109 | User Guide - Page 32
    authentication profiles are defined, they can be applied to management access methods. For example, console users can be authenticated by Authentication Profile List 1, while Telnet users are authenticated by Authentication Method List 2. Authentication methods are selected using arrows. The order
  • TP-Link TL-SG3109 | User Guide - Page 33
    The Authentication Mapping Page contains the following fields:  Console - Indicates that authentication profiles are used to authenticate console users.  Telnet - Indicates that authentication profiles are used to authenticate Telnet users.  Secure Telnet (SSH) - Indicates that authentication
  • TP-Link TL-SG3109 | User Guide - Page 34
    + servers are used. The field range is 0-65535. The default is 0.  Source IP Address - Defines the device source IP address used for the TACACS+ session between the device and the TACACS+ server.  Authentication Port (0-65535) - Defines the port number via which the TACACS+ session occurs. The
  • TP-Link TL-SG3109 | User Guide - Page 35
    . 5.1.1.6 Defining RADIUS Server Settings Remote Authorization Dial-In User Service (RADIUS) servers provide additional security for networks. RADIUS servers provide a centralized authentication method for web access. The default parameters are user-defined, and are applied to newly defined RADIUS
  • TP-Link TL-SG3109 | User Guide - Page 36
    the query, or switching to the next server. The possible field values are 1-30. Three is the default value.  Dead Time - Defines the amount of time (in minutes) that a RADIUS server is bypassed for service requests. The range is 0-2000. The default is 0 minutes.  Source IP Address - Defines the
  • TP-Link TL-SG3109 | User Guide - Page 37
    access levels for users using the Local Users Page. To define local users: 1. Click System > Management Security > Passwords > Local Users. The Local Users Page opens: Figure 39: Local Users Page The Local Users Page contains the following fields:  User Name - Displays the user name.  Access Level
  • TP-Link TL-SG3109 | User Guide - Page 38
    Confirms the new line password. The password appears in the ***** format. 2. Define the Console Line Password, Telnet Line Password, and Secure Telnet Line Password fields. 3. Redefine the security manages both access control lists and locked ports. This section contains the following topics: 31
  • TP-Link TL-SG3109 | User Guide - Page 39
    is authorized to access system services. Port-based authentication creates two access states port-based authentication also enables user-based authentication. Specific VLANs in the device are always available, even if specific ports attached to the VLAN are unauthorized. For example, Voice over IP
  • TP-Link TL-SG3109 | User Guide - Page 40
    - Enable - Enables using a Guest VLAN for unauthorized ports. If a Guest VLAN is enabled, the unauthorized port automatically joins the VLAN selected in the VLAN List field. - Disable - Disables port-based authentication on the device. This is the default.  Guest VLAN ID - Contains a list of VLANs
  • TP-Link TL-SG3109 | User Guide - Page 41
    . The device cannot provide authentication services to the client through the interface.  Enable Periodic Reauthentication - Permits immediate port reauthentication. The possible field values are: - Enable - Enables immediate port reauthentication. This is the default value. - Disable - Disables
  • TP-Link TL-SG3109 | User Guide - Page 42
    Forward - Forwards the packet. - Discard - Discards the packets. This is the default value. - Shutdown - Discards the packets and shuts down the port. The port remains shut down until reactivated, or until the device is reset.  Traps - Indicates if traps are enabled for Multiple Hosts. The possible
  • TP-Link TL-SG3109 | User Guide - Page 43
    on specific ports. Access to the locked port is limited to users with specific MAC addresses. These addresses are either manually defined on the port, or learned on that port up to the point when it is locked. When a packet is received on a locked port, and the packet TP-Link source MAC address
  • TP-Link TL-SG3109 | User Guide - Page 44
    - Discard - Discards packets from any unlearned source. This is the default value. - Shutdown - Discards packets from any unlearned source and shuts down the port. The port remains shut down until reactivated, or until the device is reset.  Trap - Enables traps when a packet is received on a locked
  • TP-Link TL-SG3109 | User Guide - Page 45
    Multicast frame rates separately on each port, and discards the frames when the rate exceeds a user-defined rate. The Storm Control Page second) at which unknown packets are forwarded. The range is 0-1,000,000. The default value is zero. All values are rounded to the nearest 64 Kbps. If the field
  • TP-Link TL-SG3109 | User Guide - Page 46
    are forwarded to the default IP when frames are sent to a remote network. The configured IP address must belong to the same IP address subnet of one of the IP interfaces. 1. Click System > System Info > IP Configuration > IP Addressing. The IP Interface Page opens: Figure 53: IP Interface Page The
  • TP-Link TL-SG3109 | User Guide - Page 47
    gateway for the system: 1. Click System > System Info > IP Configuration > IP Addressing > Default Gateway. The Default Gateway Page opens: Figure 56: Default Gateway Page The Default Gateway Page contains the following fields:  User Defined Default Gateway - Indicates the name of the current
  • TP-Link TL-SG3109 | User Guide - Page 48
    interfaces. 2. Click . The Add IP Interface Page page opens: Figure 58: Add IP Interface Page 3. Select the Interface (Port, LAG or VLAN). 4. Enter entry is deleted from the table. The range is 1 - 40000000. The default value is 60000 seconds.  Clear ARP Table Entries - Specifies the types of
  • TP-Link TL-SG3109 | User Guide - Page 49
    : Figure 60: Add ARP Entry Page 5. Select the Interface (Port, LAG or VLAN). 6. Define the IP Address and the MAC Address. 7. Click . The new entry converts user-defined domain names into IP addresses. Each time a domain name is assigned, the DNS service translates the name into a numeric IP
  • TP-Link TL-SG3109 | User Guide - Page 50
    reset. - Unselected - Deactivates the selected DNS server after the device is reset. This is the default value. 2. Click the Enable DNS checkbox. 3. Define the Default System > System Info > IP Configuration > Domain Name System a user-defined default domain name. When defined, the default domain
  • TP-Link TL-SG3109 | User Guide - Page 51
    Figure 64: Add DNS Host Page 3. Enter the Host Name and IP Address. 4. Click . The new DNS host is added to the hosts list in the Host Mapping Page. 44
  • TP-Link TL-SG3109 | User Guide - Page 52
    only when auto negotiation is disabled, and the port speed is set to 10M or 100M. This field cannot be configured on LAGs. The possible field values are: - Full - The interface supports transmission between the device and its link partner in both directions simultaneously. - Half - The interface
  • TP-Link TL-SG3109 | User Guide - Page 53
    Dependent Interface) - Use for end stations. - MDIX (Media Dependent Interface with Crossover) - Use for hubs and switches.  LAG - Indicates whether the port is part of a Link Aggregation Group (LAG). The Interface Configuration LAG table contains the following fields:  LAG - Indicates whether the
  • TP-Link TL-SG3109 | User Guide - Page 54
    the bandwidth between the devices, increases port flexibility, and provides link redundancy. The TP-Link device supports both static LAGs and Link Aggregation Control Protocol (LACP) LAGs. LACP LAGs negotiate aggregating port links with other LACP ports located on a different device. If the
  • TP-Link TL-SG3109 | User Guide - Page 55
    different media types if the ports are operating at the same speed. Aggregated links can be set up manually or automatically established by enabling LACP on the relevant links. Aggregate ports can be linked into linkaggregation port-groups. Each group is comprised of ports with the same speed. The
  • TP-Link TL-SG3109 | User Guide - Page 56
    LACP Parameters Settings Page 3. Define the Port Priority and LACP Timeout settings. 4. Click . The LACP settings are saved and the device is updated. 7.3 Configuring VLANs VLANs are logical subgroups with a Local Area Network (LAN) which combine user stations and network devices into a single
  • TP-Link TL-SG3109 | User Guide - Page 57
    Static - Indicates the VLAN is user-defined. - Default - Indicates the VLAN is the default VLAN.  Unauthenticaed VLAN - Indicates whether unauthorized users can access a Guest VLAN. Page contains a table that maps VLAN parameters to ports. Ports are assigned VLAN membership by toggling through the
  • TP-Link TL-SG3109 | User Guide - Page 58
    Dynamic - Indicates the VLAN was dynamically created through GARP. - Static - Indicates the VLAN is user-defined. - Default - Indicates the VLAN is the default VLAN.  Port - Indicates the port membership.  LAG - Indicates the LAG membership.  U - Indicates the interface is an untagged VLAN member
  • TP-Link TL-SG3109 | User Guide - Page 59
    device. Ingress filtering discards packets that are defined to VLANs of which the specific port is not a member. - Disable - Disables ingress filtering on the device.  Reserve VLAN - Indicates that the VLAN selected by the user is reserved, if not in use by the system. To modify VLAN interface or
  • TP-Link TL-SG3109 | User Guide - Page 60
    the port or LAG on which GARP is enabled.  Join Timer- Indicates the amount of time, in centiseconds, that PDUs are transmitted. The default value state. The leave all time must be greater than the leave time. The default value is 1000 centiseconds. 2. In the Copy From Entry Number field, enter
  • TP-Link TL-SG3109 | User Guide - Page 61
    - Enables GVRP on the selected device. - Disable - Disables GVRP on the selected device.  Interface - Displays the port on which GVRP is enabled. The possible field values are: - Port - Indicates the port number on which GVRP is enabled. - LAG - Indicates the LAG number on which GVRP is enabled
  • TP-Link TL-SG3109 | User Guide - Page 62
    the device. Static addresses are configured manually. An address becomes associated with a port by learning the port from the frame's source address, but static MAC addresses from being deleted when the device is reset, ensure that the port attached to the MAC address is locked. To define Static
  • TP-Link TL-SG3109 | User Guide - Page 63
    table contains address parameters by which packets are directly forwarded to the ports. The Dynamic Address Table can be sorted by interface, VLAN, before being timed out, if no traffic from the source is detected. The default value is 300 seconds.  Clear Table - Clears the Current Address Table.
  • TP-Link TL-SG3109 | User Guide - Page 64
    1. Click System > Bridging Config > Forwarding Database > Dynamic Addresses. The Dynamic Addresses Page opens. 2. Select the Interface, the MAC Address, and the VLAN ID. 3. Select an Address Table Sort Key. 4. Click . The Dynamic MAC Address Table is queried, and the results are displayed in the
  • TP-Link TL-SG3109 | User Guide - Page 65
    in increased traffic and reducing network efficiency. The TP-Link device supports the following STP versions:  Classic STP - various load balancing scenarios. For example, if port A is blocked in one STP instance, the same port can be placed in the Forwarding State in This is the default value. 58
  • TP-Link TL-SG3109 | User Guide - Page 66
    switches or bridges are running STP, each is assigned a priority. After exchanging BPDUs, the device with the lowest priority value becomes the Root Bridge. The default value is 32768. The port the bridge was initialized or reset, and the last topographic change information for Link Aggregated Groups.
  • TP-Link TL-SG3109 | User Guide - Page 67
    - Disabled - Disables the STP on the port.  Fast Link - Indicates if Fast Link is enabled on the port. If Fast Link mode is enabled for a port, the Port State is automatically placed in the Forwarding state when the port link is up. Fast Link optimizes the STP protocol convergence. STP convergence
  • TP-Link TL-SG3109 | User Guide - Page 68
    , packets from each network layer protocol can be sent over the link. The link remains configured for communications until explicit LCP or NCP packets close the link, or until some external event occurs. This is the actual switch port link type. It may differ from the administrative state. - Disable
  • TP-Link TL-SG3109 | User Guide - Page 69
    Activate Protocol Migration - Indicates whether sending Link Control Protocol (LCP) packets to configure and test the data link is enabled. The possible field values are load balancing scenarios. For example, while port A is blocked in one STP instance, the same port can be placed in the Forwarding
  • TP-Link TL-SG3109 | User Guide - Page 70
    contains the following fields:  Region Name - Indicates the name of the user- defined STP region.  Revision - Indicates that an unsigned 16-bit is discarded. Once the BPDU is discarded, the port information is aged out. The possible field range is 1-40. The default value is 20 hops.  IST Master -
  • TP-Link TL-SG3109 | User Guide - Page 71
    possible range is 0-15.  Interface - Displays the interface for which the MSTP settings are displayed. The possible field values are: - Port - Specifies the port for which the MSTP settings are displayed. - LAG - Specifies the LAG for which the MSTP settings are displayed.  Role - Indicates the
  • TP-Link TL-SG3109 | User Guide - Page 72
    .  Designated Cost - Indicates that the default path cost is assigned according to the method selected on the Spanning Tree Global Settings page.  Designated Bridge ID - Displays the ID of the bridge that connects the link or shared LAN to the root.  Designated Port ID - Displays the ID of the
  • TP-Link TL-SG3109 | User Guide - Page 73
     Which ports want to join which Multicast groups.  Which ports have Multicast 1. Click System > Bridging Config > Multicast Support > IGMP Snooping. The IGMP Snooping Page host waits to receive a message before timing out. The default time is 260 seconds.  MRouter Timeout - Indicates the amount
  • TP-Link TL-SG3109 | User Guide - Page 74
    switch notifies the Multicast device to stop sending traffic The Leave Timeout value is either user-defined, or an immediate leave value. The default assigns ports to a specific Multicast service address group. To define multicast groups: 1. Click System > Bridging Config > Multicast Support >
  • TP-Link TL-SG3109 | User Guide - Page 75
    Address - Identifies the Multicast group MAC address/IP address.  Port - Displays the port that can be added to a Multicast service.  LAG - Displays the LAG that can be added to a Multicast service. The following table contains the IGMP port and LAG members management settings: Table 5: IGMP
  • TP-Link TL-SG3109 | User Guide - Page 76
    service. The following table summarizes the Multicast settings which can be assigned to ports, using the Multicast Forward All Page. Table 6: Bridge Multicast Forward All Router/Port Control Settings Table Port Control D S F N Definition Attaches the port to the Multicast router or switch
  • TP-Link TL-SG3109 | User Guide - Page 77
    v3 applies access control and a new traps mechanism. In addition, User Security Model (USM) parameters are defined for SNMPv3, including:  Management - Defines key generation, key updates, and key use. The device supports SNMP notification filters based on Object IDs (OIDs). OIDs are used by the
  • TP-Link TL-SG3109 | User Guide - Page 78
    octets - MAC address of the device. 2. Define the Local Engine ID and Use Default fields. 3. Click . The SNMP global security parameters are set, and the device Page contains the following fields:  View Name - Displays the user-defined views. The view name can contain a maximum of 30
  • TP-Link TL-SG3109 | User Guide - Page 79
    Page opens: Figure 103: SNMP Security Group Profile Page The SNMP Security Group Profile Page contains the following fields:  Group Name - Displays the user-defined group to which access control rules are applied. The field range is up to 30 characters.  Security Model - Defines the SNMP version
  • TP-Link TL-SG3109 | User Guide - Page 80
    Group Membership Page opens: Figure 106: SNMP Security Group Membership Page The SNMP Security Group Membership Page contains the following fields:  User Name - Contains a list of user-defined user names. The field range is up to 30 alphanumeric characters.  Group Name - Contains a list of
  • TP-Link TL-SG3109 | User Guide - Page 81
    hexadecimal digits. Each byte can be separated by a period or colon.  Password - Defines the password for the group member 3. Define the User Name, Group Name, Engine ID, Authentication Method, Password, Authentication Key, and Privacy Key fields. 4. Click . The SNMP group membership is modified
  • TP-Link TL-SG3109 | User Guide - Page 82
    following fields:  Management Station - Displays the management station IP address for which the basic SNMP community is defined.  well as permissions to modify the community.  View Name - Contains a list of user-defined SNMP views  Remove - Removes a community. The possible field values are:
  • TP-Link TL-SG3109 | User Guide - Page 83
    the device is updated. 11.4.2 Defining Notification Filters The SNMP Notification FiIter Page permits filtering traps based on OIDs. Each OID is linked to a device feature or a portion of a feature. The SNMP Notification FiIter Page also allows network managers to filter notifications. To define
  • TP-Link TL-SG3109 | User Guide - Page 84
    Page contains information for defining filters that determine whether traps are sent to specific users, and the trap type sent. SNMP notification filters provide the following services:  Identifying Management Trap Targets  Trap Filtering  Selecting Trap Generation Parameters  Providing Access
  • TP-Link TL-SG3109 | User Guide - Page 85
    that SNMP Version 1 traps are sent. - SNMP V2c - Indicates that SNMP Version 2 traps are sent.  UDP Port - Displays the UDP port used to send notifications. The field range is 1-65535. The default is 162.  Filter Name - Indicates if the SNMP filter for which the SNMP Notification filter is defined
  • TP-Link TL-SG3109 | User Guide - Page 86
    . The Add SNMP Notification Receiver Page opens: Figure 116: Add SNMP Notification Receiver Page 3. Define the Recipient IP, Notification Type, SNMPV1,v2c or SNMPv3, UPD Port, Filter Name, Timeout, and Retries fields. 4. Click . The SNMP Notification recipients are defined, and the device is
  • TP-Link TL-SG3109 | User Guide - Page 87
    be selected, or the output service fields can be selected, including:  VLAN Priority Tags (VPT) - VPTs are mapped to an output queues based on the VPT. While queue mapping is user- defined, the VPT default mapping to the output queue is as follows. In the VPT default mapping, Queue 1 has the lowest
  • TP-Link TL-SG3109 | User Guide - Page 88
    enabled or disabled per port.  Default CoS- Packets arriving untagged are assigned to a default VPT, which can be set by the user on a per port basis. Once the VPT Best Effort service. After packets are assigned to a specific queue, using the chosen classification method various services can be
  • TP-Link TL-SG3109 | User Guide - Page 89
    Mode Basic Mode supports activating one of the following Trust settings:  VLAN Point Tag  DiffServ Code Point  None In addition, a single IP-based ACL can bandwidth management. After assigning packets to a specific queue, services such as configuring output queues for the scheduling scheme, or
  • TP-Link TL-SG3109 | User Guide - Page 90
    CoS value for incoming packets for which a VLAN tag is not defined. The possible field values are 0-7. The default CoS is 0. 2. Select Enable in the Quality of Service field. 3. Select the Trust Mode. 4. Click . QoS is configured and enabled on the device. To modify interface settings: 1. Click
  • TP-Link TL-SG3109 | User Guide - Page 91
    Page opens: Figure 121: CoS to Queue Page  Class of Service - Specifies the CoS priority tag values, where zero is the supported, where zero is the lowest and 8 is the highest.  Restore Defaults - Allows you to restore default settings. 2. Modify the Queue values or select Restore Defaults
  • TP-Link TL-SG3109 | User Guide - Page 92
    1. Click System > Quality of Service > Queue Mapping > DSCP to Queue. The DSCP to Queue Page opens: Figure traffic forwarding queue to which the DSCP priority is mapped. Four traffic priority queues are supported. 2. Modify the Queue values. 3. Click updated. . The DSCP to Queue mapping is 85
  • TP-Link TL-SG3109 | User Guide - Page 93
    download, the new version is marked, and is used after the device is reset. This section contains the following topics:  Downloading System Files  Uploading System the following fields:  Firmware Download - Indicates that the download is for firmware. If Firmware Download is selected, the
  • TP-Link TL-SG3109 | User Guide - Page 94
    13.1.2 Firmware Download The Firmware Download section contains the following fields:  TFTP Server IP Address - Specifies the address of the TFTP server from which files are downloaded.  Source File Name - Specifies the file to be downloaded.  Destination File - Specifies
  • TP-Link TL-SG3109 | User Guide - Page 95
    Configuration Upload section contains the following fields:  TFTP Server IP Address - Specifies the address of the TFTP server to which Activating Image Files The Active Image Page allows network managers to select and reset the Image files. To download system files: 1. Click System > Maintenance
  • TP-Link TL-SG3109 | User Guide - Page 96
    - Indicates the Startup Configuration file is selected.  Restore Configuration Factory Defaults - Resets the Configuration file to the factory defaults. The factory defaults are reset after the device is reset. When unselected, the device maintains the current Configuration file. 2. Select
  • TP-Link TL-SG3109 | User Guide - Page 97
    values are: - RX - Defines the port mirroring on receiving ports. - TX - Defines the port mirroring on transmitting ports. - Both - Defines the port mirroring on both receiving and transmitting ports. This is the default value.  Remove - Removes the port mirroring session. The possible field values
  • TP-Link TL-SG3109 | User Guide - Page 98
    Diagnostics > Copper Cable. The Copper Cable Page opens: Figure 130: Copper Cable Page The Copper Cable Page contains the following fields:  Port - Specifies the port to which the cable is connected.  Test Result - Displays the cable test results. Possible values are: - No Cable - Indicates that
  • TP-Link TL-SG3109 | User Guide - Page 99
    cables. Note: Optical transceiver diagnostics can be performed only when the link is present. To test cables:  Click System > Maintenance > Page The Optical Transceivers Page contains the following fields:  Port - Displays the port IP address on which the cable is tested.  Temperature -
  • TP-Link TL-SG3109 | User Guide - Page 100
    the following fields:  Interface - Indicates the device for which statistics are displayed. The possible field values are: - Port - Defines the specific port for which interface statistics are displayed. - LAG - Defines the specific LAG for which interface statistics are displayed.  Refresh
  • TP-Link TL-SG3109 | User Guide - Page 101
    in the Interface field. The interface statistics are displayed. To reset interface statistics counters: 1. Open the Interface Statistics Page. statistics are displayed. The possible field values are: - Port - Defines the specific port for which Etherlike statistics are displayed. - LAG - Defines
  • TP-Link TL-SG3109 | User Guide - Page 102
    , select another rate from the Refresh Rate dropdown list. To reset Etherlike interface statistics counters: 1. Open the Etherlike Statistics Page. - Displays the device GVRP Invalid Event statistics. 2. Select an interface (Port or LAG) in the Interface field. The GVRP statistics are displayed. To
  • TP-Link TL-SG3109 | User Guide - Page 103
    EAPOL frame.  Last Frame Source - Indicates the source MAC address attached to the most recently received EAPOL frame. 2. Select a port from the Port dropdown list. The port statistics are displayed. To update the refresh time:  To change the refresh rate for statistics, select another rate from
  • TP-Link TL-SG3109 | User Guide - Page 104
    contains the following fields:  Interface - Indicates the device for which statistics are displayed. The possible field values are: - Port - Defines the specific port for which RMON statistics are displayed. - LAG - Defines the specific LAG for which RMON statistics are displayed.  Refresh Rate
  • TP-Link TL-SG3109 | User Guide - Page 105
    Refresh Rate dropdown list. To reset RMON statistics counters: 1. are taken from the ports. The field range is 1-3600. The default is 1800 seconds ( default value is 50.  Current Number of Samples in List - Displays the current number of samples taken.  Owner - Displays the RMON station or user
  • TP-Link TL-SG3109 | User Guide - Page 106
    the following fields:  History Entry No. - Displays the entry number for the History Control Table page.  Owner - Displays the RMON station or user that requested the RMON information. The field range is 0-20 characters.  Sample No. - Indicates the sample number from which the statistics were
  • TP-Link TL-SG3109 | User Guide - Page 107
    and a trap. - None - Indicates that no event occurred.  Time - Displays the time that the event occurred.  Owner - Displays the device or user that defined the event.  Remove - Removes a RMON event. The possible field values are: - Checked - Removes a selected RMON event. - Unchecked - Maintains
  • TP-Link TL-SG3109 | User Guide - Page 108
    Events Control Page, and the device is updated. To modify an RMON Event user: 1. Click System > Statistics > RMON > Events. The RMON Events Control fields for setting network alarms. Network alarms occur when a network problem, or event, is detected. Rising and falling thresholds trigger alarms.
  • TP-Link TL-SG3109 | User Guide - Page 109
    values are: - Port - Displays the RMON statistics for the selected port. - LAG - or in the management system. If the device is not reset, the entry remains in the Log Table. - TRAP Alarm User Page opens: Figure 146: Add RMON Alarm User Page 3. Define the fields. 4. Click . The RMON alarm user is
  • TP-Link TL-SG3109 | User Guide - Page 110
    Figure 147: Edit RMON Alarm User Page 2. Modify the fields. 3. Click . The entry is updated in the RMON Alarm Page, and the device is updated. 103
  • TP-Link TL-SG3109 | User Guide - Page 111
    ACL Aggregated VLAN AH ARP Definition Specifies the method by which user access is granted to the system. Allows network managers to Protocol. • Protocol ID. • Source Port. • Destination Port. • Wildcard Mask. • Source IP Address. • Destination IP Address. Access Control List. Access Control
  • TP-Link TL-SG3109 | User Guide - Page 112
    an IP address of a BootP server on a network, or a configuration file loaded into the boot of a device. Bridge Protocol Data Unit. Provide bridging information in a message format. BPDUs are sent across switch information with in Spanning Tree configuration. BPDU packets contain information on ports
  • TP-Link TL-SG3109 | User Guide - Page 113
    control based on destination address. Port from which network traffic is transmitted. Enhanced Interior Gateway Routing Protocol. Provides fast convergence, support for variable-length subnet mask, and supports multiple network layer protocols. An end user device on a network. Exterior Gateway
  • TP-Link TL-SG3109 | User Guide - Page 114
    and supports data transfer rates of Mpbs. A newer version called Fast Ethernet supports 100 changing. For example, an STP port constantly changes from listening to learning -point link to remote IP internetwork acts as a source of information or services to other computers. Allows specific modules to
  • TP-Link TL-SG3109 | User Guide - Page 115
    . Multicast routing copies one packet to several ports. IP Version 6. Provides a newer version of the Internet Protocol, and follows IP version 4 (IPv4). IPv6 increases the IP address size from 32 bits to 128 bits. In addition, IPv6 support more levels of addressing hierarchy, more addressable
  • TP-Link TL-SG3109 | User Guide - Page 116
    Tunneling Protocol (PPTP). Link Aggregated Group. Aggregates ports or VLANs into a single virtual port or VLAN. Local or excludes certain values, for example parts of an IP address. Message Digest 5. An algorithm that produces a A cable used for hubs and switches. Multiply-Divide Unit. A high-speed
  • TP-Link TL-SG3109 | User Guide - Page 117
    load balancing. Blocks of information for transmission in packet switched systems. Protocol Data Unit. A data unit specified in a layer protocol consisting of protocol control information and layer user data. Packet Internet Groper. Verifies if a specific IP address is available. A packet is sent to
  • TP-Link TL-SG3109 | User Guide - Page 118
    Subnet Definition Provides duplication of devices, services, or events. If a device, service, or event fails, redundancy provides a Subnets are portions of a network that share a common address component. In TCP/IP networks, devices that share a prefix are part of the same subnet. For example
  • TP-Link TL-SG3109 | User Guide - Page 119
    or part of an IP address used in a subnet address. Switch Filters and forwards packets between LAN segments. Switches support any packet protocol type. occurred. Link Aggregation. Optimizes port usage by linking a group of ports together to form a single trunk (aggregated groups). User Data Protocol
  • TP-Link TL-SG3109 | User Guide - Page 120
    71035590 TP-LINK TECHNOLOGIES CO., LTD. E-mail: [email protected] Website: http://www.tp-link.com Add: 3/F., Building R1-B, Hi-tech Industrial Park, Shennan Rd., Shenzhen, P.R.China
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
TL-SG3109
Embedded Web System User Guide
TL-SL3428
9-port Gigabit Managed Switch
24+4G Gigabit Managed Switch
TL-SL3452
48+4G Gigabit Managed Switch
Rev:
1.0