TomTom RIDER 2nd Edition User Guide - Page 16

Battery cable, Taking care of your TomTom RIDER

Get TomTom RIDER 2nd Edition PDF manuals and user guides
UPC - 636926016841
View all TomTom RIDER 2nd Edition manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

3. Close the Holder. Make sure that your RIDER is held firmly in place. You are now ready to make your first trip with your TomTom RIDER. Battery cable The battery cable can optionally be used to power and charge your TomTom RIDER from your motorcycle battery. Note: If you are unsure about setting up the battery cable, consult your local motorcycle garage. Connect the battery cable connector to the power connector on the holder. Connect the red battery cable to the switched positive 12 volt power supply on your motorcycle and the black battery cable to the ground supply on your motorcycle. Make sure that the battery cable is secured safely to your motorcycle. It must not hang from the frame or interfere with the motorcycle in any way. Make sure that it is also not in contact with any areas of the motorcycle that become hot and may melt the cable. Taking care of your TomTom RIDER It is important to take care of your RIDER and to clean it correctly. • Use the screen cloth provided to wipe the screen of your RIDER; do not use any liquid cleaners. • Only open the compartment that contains the memory card slot when you are indoors. Do not open the compartment when your RIDER is wet. • When carrying your RIDER, always use the RIDER case provided. • If your RIDER gets wet, dry it with a soft cloth. • Do not open the casing of your RIDER under any circumstances. • Do not use the memory card (SD card) with any device other than your RIDER. Other devices may damage the memory card. • • 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
16
•
•
•
•
•
•
3. Close the Holder. Make sure that your RIDER is held firmly in place.
You are now ready to make your first trip with your TomTom RIDER.
Battery cable
The battery cable can optionally be used to power and charge your
TomTom RIDER from your motorcycle battery.
Connect the battery cable connector to the power connector on the holder.
Connect the red battery cable to the switched positive 12 volt power supply
on your motorcycle and the black battery cable to the ground supply on your
motorcycle.
Make sure that the battery cable is secured safely to your motorcycle. It must
not hang from the frame or interfere with the motorcycle in any way. Make
sure that it is also not in contact with any areas of the motorcycle that become
hot and may melt the cable.
Taking care of your TomTom RIDER
It is important to take care of your RIDER and to clean it correctly.
•
Use the screen cloth provided to wipe the screen of your RIDER; do not use
any liquid cleaners.
•
Only open the compartment that contains the memory card slot when you
are indoors. Do not open the compartment when your RIDER is wet.
•
When carrying your RIDER, always use the RIDER case provided.
•
If your RIDER gets wet, dry it with a soft cloth.
•
Do not open the casing of your RIDER under any circumstances.
•
Do not use the memory card (SD card) with any device other than your
RIDER. Other devices may damage the memory card.
Note
: If you are unsure about setting up the battery cable, consult your local
motorcycle garage.