Toshiba 32AF62 Owners Manual - Page 17

Selecting the Signal Source / Programming Channels into the TV's Memory

Get Toshiba 32AF62 PDF manuals and user guides View all Toshiba 32AF62 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Welcome to Toshiba Connecting your TV Using the Remote Control Selecting the signal source To select the signal source to view: 1. Press TV/VIDEO on the remote control or the TV. 2. Use the CHANNEL NUMBERS on the remote control to select the number (0-5) that corresponds with the desired source. (You can also repeatedly press the TV/VIDEO button on either the remote control or the TV to cycle through the sources.) TV Front Panel DEMO MENU TV/VIDEO VOLUME CHANNEL TV/VIDEO SOURCE SELECTION 0: ANT 1 1: VIDEO 1 2: VIDEO 2 3: VIDEO 3 4: ColorStream 5: ANT 2 0-5: TO SELECT To display the current signal source: Press TV/VIDEO or RECALL. The current source displays in purple. Programming channels into the TV's memory When you press CHANNEL ▲▼ on the TV or remote control, the TV stops only on the channels stored in the TV's memory. Note: To tune the TV to a channel not programmed into the memory, use the CHANNEL NUMBERS on the remote control. Follow the steps below and on the next page to program channels into the TV's memory. Programming channels automatically Your TV can automatically detect all active channels in your area and store them in the TV's memory. After the channels are stored automatically, you can manually add or erase individual channels (see page 18). If you use both ANT-1 and ANT-2 terminals, you will need to program channels for each signal source. To program channels automatically: 1. Press MENU. 2. Press x or • to highlight the SET UP menu. 3. Press y or z to highlight TV/CABLE. 4. Press x or • to highlight TV (if you use an antenna) or CABLE (if you use cable). 5. Press z to highlight CH PROGRAM. LIGHT RECALL POWER TV CABLE VCR MUTE TV/VIDEO TIMER 12 45 3 CH 6 78 9 VOL CH RTN 100 0 ENT ADV/ PIP CH FAV ENTER FAV C.CAPT EXIT MENU RESET ADV/ PIP CH STOP SOURCE PLAY PIP REC TV/VCR REW FF STILL LOCATE SWAP CT-9946 RECALL TV/VIDEO CH (Channel) Channel Numbers MENU Setting up your TV Using the TV's Features Appendix SET UP LANGUAGE: [ENGLISH] FRANCAIS ESPANOL ANT1/2: [ANT1] ANT2 TV/CABLE: [TV] CABLE CH PROGRAM ADD/ERASE: [ADD] ERASE MORE MOVE [ ] SELECT [ ] SET UP LANGUAGE: [ENGLISH] FRANCAIS ESPANOL ANT1/2: [ANT1] ANT2 TV/CABLE: [TV] CABLE CH PROGRAM ADD/ERASE: MORE [ADD] ERASE MOVE [ ] SELECT [ ] 6. Press x or • to start automatic channel programming ("CH PROGRAM" displays on-screen). The TV automatically cycles through every TV or cable channel (depending on which you selected), and stores all active channels in the TV's memory. 7. When automatic channel programming is complete, the message "CH Programming Completed" appears. 8. Press CHANNEL ▲▼ to view the programmed channels. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
W
elcome to
T
oshiba
Connecting
y
our TV
Using the
Remote Control
Setting up
y
our TV
Using the TV’s
F
eatures
Appendix
17
Selecting the signal source
To select the signal source to view:
1. Press
TV/VIDEO
on the remote control or the TV.
2.
Use the
CHANNEL NUMBERS
on the remote control to select
the number (0–5) that corresponds with the desired source.
(You can also repeatedly press the
TV/VIDEO
button on either the
remote control or the TV to cycle through the sources.)
0–5: TO SELECT
SOURCE SELECTION
0:
ANT 1
1:
VIDEO 1
2:
VIDEO 2
3:
VIDEO 3
4:
ColorStream
5:
ANT 2
To display the current signal source:
Press
TV/VIDEO
or
RECALL
. The current source displays in
purple.
Programming channels into the TV’s memory
When you press
CHANNEL
▲▼
on the TV or remote control,
the TV stops only on the channels stored in the TV’s memory.
Note:
To tune the TV to a channel not programmed into the memory,
use the
CHANNEL NUMBERS
on the remote control.
Follow the steps below and on the next page to program channels into
the TV’s memory.
Programming channels automatically
Your TV can automatically detect all active channels in your area and
store them in the TV’s memory. After the channels are stored auto-
matically, you can manually add or erase individual channels (see
page 18).
If you use both ANT-1 and ANT-2 terminals, you will need to
program channels for each signal source.
To program channels automatically:
1. Press
MENU
.
2. Press
x
or
•
to highlight the SET UP menu.
3. Press
y
or
z
to highlight TV/CABLE.
4. Press
x
or
•
to highlight TV (if you use an antenna) or CABLE (if
you use cable).
5. Press
z
to highlight CH PROGRAM.
MOVE
SELECT
[
]
[
]
LANGUAGE:
ANT1/2:
TV/CABLE:
CH PROGRAM
ADD/ERASE:
MORE
[ENGLISH] FRANCAIS ESPANOL
[ANT1] ANT2
[TV]
CABLE
[ADD] ERASE
SET UP
MOVE
SELECT
[
]
[
]
LANGUAGE:
ANT1/2:
TV/CABLE:
CH PROGRAM
ADD/ERASE:
MORE
[ENGLISH] FRANCAIS ESPANOL
[ANT1] ANT2
[TV] CABLE
[ADD] ERASE
SET UP
6. Press
x
or
•
to start automatic channel programming (“CH
PROGRAM” displays on-screen). The TV automatically cycles
through every TV or cable channel (depending on which you
selected), and stores all active channels in the TV’s memory.
7.
When automatic channel programming is complete, the message
“CH Programming Completed” appears.
8. Press
CHANNEL
▲▼
to view the programmed channels.
DEMO
MENU
TV/VIDEO
VOLUME
CHANNEL
T
V F
r
ont P
anel
TV/VIDEO
CH RTN
ADV/
PIP CH
ADV/
PIP CH
LIGHT
MUTE TV/VIDEO TIMER
RECALL POWER
TV
CABLE
VCR
ENT
ENTER
PLAY
PIP
REC
STILL
LOCATE
SWAP
TV/VCR
REW
FF
STOP
SOURCE
FAV
FAV
C.CAPT
EXIT
MENU
RESET
1
4
2
5
3
6
7
8
9
0
100
Channel
Numbers
MENU
CH
CH (Channel)
VOL
CT-9946
RECALL
TV/VIDEO