Toshiba 50A11 Owners Manual - Page 20
Adjusting the Color Convergence, will turn completely white when correctly adjusted. When color
View all Toshiba 50A11 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 20 highlights
Index Appendix Using the TV's Features Setting up your TV Using the Remote Control Connecting your TV Introduction Adjusting the color convergence This projection TV uses three separate TV tubes: red, green, and blue. The red, green, and blue images are projected onto the screen where they converge to form a full-color picture. You can see a clear picture only when the three images converge correctly. Convergence may drift over time or if the TV is moved. If you can see clear images on the screen, skip this procedure. Make this adjustment after the TV has been on for at least 30 minutes. To check and adjust the color convergence: 1. Press MENU, then press x or • until the PICTURE menu appears. 2. Press y or z to highlight CONVERGENCE (see illustration below left). 3. Press x or • to display the center CONVERGENCE menu (see illustration below right). 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 1 1 2 2 3 3 4 4 5 5 6 6 7 P I CTURE ANTENNA 7 8 8 9 MODE SPORTS 9 10 10 11 11 12 FLESH TONE ON 12 13 NO I SE REDUCTION OFF 13 14 COLOR 14 15 TEMPERATURE COOL 15 16 CONVERGENCE 16 17 SAVE NEW PREFERENCE 17 18 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 RED B L U E ENTER : TO SELECT COLOR EX I T : TO SELECT POS I T I ON 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 If you see separate red, blue, or green crossed lines (or red or blue shadows next to white lines), you need to adjust the convergence. 4. Press ENTER to highlight RED or BLUE, depending on which color needs adjusting. If both red and blue need adjusting, perform steps 4 and 5 twice. 5. Press y (up), z (down), x (left), or • (right) on the remote control to converge the red or blue line into the green line, which will turn completely white when correctly adjusted. When color convergence is correctly adjusted, you will see two single white lines. 6. Press EXIT to close the center CONVERGENCE menu and open the circumference CONVERGENCE menu (see illustration below left). 7. Press the corresponding Number button (1-4 and 6-9) to select the area to adjust. 8. Press ENTER to highlight RED or BLUE (see illustration below right), depending on which color needs adjusting. If both red and blue need adjusting in the selected area, perform steps 8 and 9 twice. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 1 1 2 3 2 3 4 5 6 7 8 4 6 9 10 11 12 PUSH 1 - 9 13 14 15 16 7 8 9 17 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 1 2 3 4 5 6 7 8 9 10 11 12 13 RED BLUE 14 15 ENTER : TO SELECT COLOR 16 EX I T : TO SELECT POS I T I ON 17 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 9. Press yzx • to converge the red or blue line into the green line, which will turn completely white when correctly adjusted. Repeat steps 8 and 9 until you see two single crossed white lines. 10. Press EXIT once to select another area to adjust, and then repeat steps 7-9. 11. Press EXIT twice to close the CONVERGENCE menu. 20 RECALL MUTE POWER 123 456 78 9 CH RTN 100 0 ENT Number CH VOL MENU/ ENTER VOL TV CABLE VCR CH EX I T FAV CH TV/VIDEO MENU/ ENTER yzx • EXIT