Toshiba 72HM196 Operating Guide - Page 82

How to replace the lamp unit

Page 82 highlights

HM196_EN.book Page 82 Tuesday, May 30, 2006 2:18 PM Chapter 9: Appendix How to replace the lamp unit WARNING: RISK OF ELECTRIC SHOCK! TO REDUCE THE RISK OF ELECTRIC SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS SPECIFIED HEREIN. REFER ALL SERVICING NOT SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE PERSONNEL. Failure to follow this WARNING may result in death or serious injury. Required tools: • Manual screwdrivers (Phillips and slotted) • Soft, lint-free gloves • Optional tool: 5/16" nut driver 1 Turn off the TV and unplug the power cord. WARNING: Eye damage may result from directly viewing the light produced by this lamp. Always turn off the TV and unplug the power cord before opening the lamp unit door. 2 STOP! Allow the lamp to cool for at least one (1) hour before replacing it. 4 Using a manual Phillips screwdriver, loosen the two screws on the lamp unit. Lamp unit screws WARNING: RISK OF ELECTRIC SHOCK! The lamp unit door is provided with an interlock to reduce the risk of electric shock and excessive ultraviolet radiation. Never defeat its purpose or attempt to service without removing the lamp unit door completely. Failure to follow this WARNING may result in death or serious injury. 5 Grasp the lamp unit handle and gently pull the lamp unit straight out of the TV. Set the old lamp unit aside (- "Disposing of the used lamp unit" on page 83). 3 On the lamp unit door on the side of the TV, loosen the screw using a manual screwdriver, and then remove the lamp unit door. TV back Lamp unit door detail NOTE: Wear soft, lint-free gloves when replacing the lamp unit. 6 Carefully insert the new lamp unit straight into the TV until it is fully seated. Loosen screw using manual screwdriver 82 HM196 (E/F) Web 213:276

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92

82
HM196 (E/F) Web 213:276
Chapter 9: Appendix
How to replace the lamp unit
Required tools:
Manual screwdrivers (Phillips and slotted)
Soft, lint-free gloves
Optional tool: 5/16" nut driver
1
Turn off the TV and unplug the power cord.
2
STOP!
Allow the lamp to cool for at least one (1) hour
before replacing it.
3
On the lamp unit door on the side of the TV, loosen the
screw using a manual screwdriver, and then remove the
lamp unit door.
4
Using a manual Phillips screwdriver, loosen the two
screws on the lamp unit.
5
Grasp the lamp unit handle and gently pull the lamp unit
straight out of the TV. Set the old lamp unit aside
(
-
“Disposing of the used lamp unit” on page 83).
6
Carefully insert the new lamp unit straight into the TV
until it is fully seated.
WARNING: RISK OF ELECTRIC
SHOCK!
TO REDUCE THE RISK OF ELECTRIC
SHOCK,
NEVER REMOVE TV COVERS, EXCEPT AS
SPECIFIED HEREIN.
REFER ALL SERVICING NOT
SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE
PERSONNEL. Failure to follow this WARNING may result in
death or serious injury.
WARNING: Eye damage may result from
directly viewing the light produced by
this lamp.
Always turn off the TV and unplug the power cord before
opening the lamp unit door.
TV back
Loosen screw
using manual
screwdriver
Lamp unit door detail
WARNING: RISK OF ELECTRIC
SHOCK!
The lamp unit door is provided with an
interlock to reduce the risk of electric shock and excessive
ultraviolet radiation.
Never defeat its purpose or attempt
to service without removing the lamp unit door
completely.
Failure to follow this WARNING may result in
death or serious injury.
NOTE:
Wear soft, lint-free gloves when
replacing the lamp unit.
Lamp unit screws
HM196_EN.book
Page 82
Tuesday, May 30, 2006
2:18 PM