Toshiba TDP-EX20 User Manual - Page 23

Using the menus 1 (Continued) Default setting 2 menu Item Projection mode Description Sets projection mode in accordance with Placement Style. p.23 (Standard) (Rear) (Ceiling) (Rear ceiling) Fan mode Sets the cooling fan speed. Standard High Remote control When 2 projectors are used and controlled by the remote control respectively, this menu sets the code for the projector and the remote control. [ or : Enter setting] [ : Select from 1, 2] [ : Confirm] [ :Select OK to end] Press [Cancel] to return. Key lock Lock the control panel buttons. [ or : Enter setting] [ [ :Select OK to end] Press [Cancel] to return. : Select On/Off] [ : Confirm] Lamp power Set the lamp power. Low Standard Reset all Press . (The password and user logo are not reset.) Resets all adjustments and settings to their factory settings. Yes No Password Password setting p.35 Press . Password registration/Password setting Detailed description [Fan mode] Setting [Fan mode] to [High] increases the cooling fan speed. (The cooling fan noise gets louder.) Set this option to use the projector, for example, at high altitude (over 1,500 meters above sea level). • Do not set Fan mode to [High] when using the projector at a lower altitude. [Remote control] Sets a remote control code from 2 types. You can set each code respectively for up to 2 projectors. The factory setting is [1]. To switch codes, set the same code for the projector and the remote control. A remote control code is applied after the setting is done. • You cannot operate the remote control if the codes of the projector and the remote control do not match. Remote control code setting for remote control Set the same remote control code switch as the projector. p.18 p.19 44 [Key lock] Protect from operating errors by locking on the control panel buttons of the projector. (The remote control operations are available.) Control panel operations are locked after the setting is done, and accordingly operation with the control panel buttons is disabled. • To release the key lock, set the [Key lock] to [Off] using remote control. Pressing the [RETURN] button on the projector for 10 seconds also sets the [Key lock] to [Off]. (When operating the main unit, the 2 indicators of LAMP and TEMP light in orange for 3 seconds, and at the same time the projector beeps.) However, when Network or USB memory input is selected, the [Key lock] cannot be set to [Off] with the [RETURN] button on the projector. [Lamp power] When [Lamp power] is set to [Low], the screen becomes a little darker, but the cooling fan noise gets quieter. N Displaying Information (Status display) This displays information about the input signal, lamp use time, etc. "Yes": displayed, "No": not displayed Item Input Mode name Resolution Frequency Sync Description Input source name RGB input mode [Note 1] Resolution (in dots) Sync frequency Sync signal polarity [Note 2] Computer Y/PB/PR Video S-video Network USB memory Yes Yes Yes Yes Yes Yes Yes No No No No No Yes No No No No No Yes No No No No No Yes No No No No No Signal format Y/PB/PR signal format No Yes No No No No Video mode Color method of video signal No Lamp time Time of lamp use [Note 3] Yes Lamp reset count The count for lamp replacement Yes Total time Version The total time that this projector is used. Yes Firmware version [Note 4] Yes No Yes Yes No No Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Notes 1: The mode of supported RGB signals p.94 is shown. 2: Sync signal polarity shown as P (positive) or N (negative) for [H/V]. 3: Displays [Lamp time] as a measure of when the lamp should be replaced. (Cannot be used as a counter of guaranteed lamp time.) When the displayed time approaches 2,000 hours, consult with a dealer about getting replacement for: TLPLW15 for TDP-EX20 (sold separately). 4: [Version] shows the version of the projector's internal control program. This version is referred to for customer service, etc. Note • The displayed information will not be refreshed if the status changes. To refresh the information, dismiss the display, then display it again. 45 Operations