Toshiba TDP-P7U User Guide 2 - Page 65

Mount the new lamp cartridge., Mount the lamp cover., Reset the Lamp Timer., Lamp Timer Reset

Get Toshiba TDP-P7U PDF manuals and user guides View all Toshiba TDP-P7U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Replacing the Lamp Cartridge 5 Mount the new lamp cartridge. (1) Push the lamp cartridge in slowly. (Line it up with the screw holes in the projector.) (2) Turn the lamp cartridge's two screws clockwise to tighten them. 6 Mount the lamp cover. (1) Set the tip of the lamp cover in place, then close the lamp cover. (2) Turn the lamp cover's screw clockwise to tighten it. 2 1 7 Reset the Lamp Timer. Connect the power cord, switch on the power, and then reset. Select [Info.] → [Lamp Timer Reset] on the menu and press the ENTER button. There is a change to the initialization verification display. Press the ENTER button again. See "Lamp Timer Reset" on Page E-47. Note: After reaching the lamp service life, if the lamp is used for more than another 100 hours, it will not be possible to switch on the power. Should this happen, while the projector is in the standby mode, simultaneously holding down the projector's SOURCE button and AUTO button for more than 5 seconds will clear the lamp timer. Checking that the STATUS indicator is out will show that the lamp timer has been cleared. Contact a store that sells the TDP-P7 for a replacement lamp. Indicate you need a TLP LP7 replacement lamp for the TDP-P7. E-54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
E-54
1
2
Replacing the Lamp Cartridge
5
Mount the new lamp cartridge.
(1) Push the lamp cartridge in slowly.
(Line it up with the screw holes in the projector.)
6
Mount the lamp cover.
(1) Set the tip of the lamp cover in place, then close the lamp
cover.
7
Reset the Lamp Timer.
Connect the power cord, switch on the power, and then reset.
Select [Info.]
→
[Lamp Timer Reset] on the menu and press the ENTER button. There is a change to the initialization
verification display. Press the ENTER button again. See
“
Lamp Timer Reset
”
on Page
E-47
.
Note:
After reaching the lamp service life, if the lamp is used for more than another 100 hours, it will not be possible to switch on the power. Should
this happen, while the projector is in the standby mode, simultaneously holding down the projector’s SOURCE button and AUTO button for
more than 5 seconds will clear the lamp timer. Checking that the STATUS indicator is out will show that the lamp timer has been cleared.
Contact a store that sells the TDP-P7 for a replacement lamp. Indicate you need a TLP LP7 replacement lamp for the TDP-P7.
(2) Turn the lamp cartridge
’
s two screws clockwise to tighten
them.
(2) Turn the lamp cover
’
s screw clockwise to tighten it.