Tripp Lite SUINT2000XL Owner's Manual for SUINT1000XL/SUINT2000XL/SUINT3000XL - Page 5

Basic Operation - smartonline

Get Tripp Lite SUINT2000XL PDF manuals and user guides View all Tripp Lite SUINT2000XL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

200607207 93-2525 230V Smartonline OM.qxd 11/9/2006 3:51 PM Page 5 IBmapsoicrtOanpterSaatfioetny Instructions Front Panel Switches "ON/TEST" Switch: This switch controls four separate UPS functions: UPS Power ON: To turn the UPS on, press this switch, hold it for several seconds until you hear a beep, then release it. The "ON LINE" LED will illuminate. UPS Self-Test: During normal on-line operation, press this switch and hold it until you hear a beep. This initiates a 10-second self-test of the battery. The UPS will shift to battery power (the "ON BATT" and "BATT ACTIVE METER" LEDs will illuminate) for ten seconds. Alarm Silence: To silence the UPS "on-battery" alarm, press this switch and hold it until you hear a beep. UPS Cold Start: To use your UPS as a stand-alone power source when AC power is unavailable (i.e. during a blackout), press this switch and hold it until you hear a beep. The UPS will then provide battery power to its outlets.* * The "ON BATT" Indicator Light will be illuminated since your UPS will be operating from battery power. "OFF" Switch: This switch turns power OFF at the UPS receptacles. Press this switch, hold it until you hear a beep, then release it. The UPS will continue charging and the fan will continue to cool internal components even after you turn the UPS receptacles off. To turn the UPS OFF completely, including the charger, disconnect the UPS's power cord after pressing the "OFF" switch. Front Panel Indicator Lights "ON LINE" LED: This green light will be lit when the UPS is in normal on-line operation (filtering and resynthesizing incoming AC line voltage to provide pure sine wave output). When this light is illuminated, you can monitor the load level of your UPS on the "LOAD ACTIVE METER" LEDs. "LINE" LED: This green light will be lit when the utility-supplied AC line voltage at your wall outlet is nominal. It will flash if the line voltage or frequency is outside the nominal range (either too low or too high). No action is required on your part when the LED flashes; the UPS continuously and automatically filters AC line power to provide your equipment with pure sine wave AC power, regardless of brownout or overvoltage conditions. If this light is off, then AC line voltage is not present (blackout) or is at an extremely high voltage. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
5
Basic Operation
Front Panel Switches
“ON/TEST” Switch:
This switch controls four separate UPS functions:
UPS Power ON:
To turn the UPS on, press this switch, hold it for
several seconds until you hear a beep, then release it. The “ON LINE”
LED will illuminate.
UPS Self-Test:
During normal on-line operation, press this switch
and hold it until you hear a beep. This initiates a 10-second self-test
of the battery. The UPS will shift to battery power (the “ON BATT”
and “BATTACTIVE METER” LEDs will illuminate) for ten seconds.
Alarm Silence:
To silence the UPS “on-battery” alarm, press this
switch and hold it until you hear a beep.
UPS Cold Start:
To use your UPS as a stand-alone power source
when AC power is unavailable (i.e. during a blackout), press this
switch and hold it until you hear a beep. The UPS will then provide bat-
tery power to its outlets.*
* The “ON BATT” Indicator Light will be illuminated since your UPS will be operating
from battery power.
“OFF” Switch:
This switch turns power OFF at the UPS receptacles.
Press this switch, hold it until you hear a beep, then release it. The
UPS will continue charging and the fan will continue to cool internal
components even after you turn the UPS receptacles off. To turn the
UPS OFF completely, including the charger, disconnect the UPS’s
power cord after pressing the “OFF” switch.
“ON LINE” LED:
This green light will be lit when the UPS is in normal
on-line operation (filtering and resynthesizing incoming AC line voltage
to provide pure sine wave output). When this light is illuminated, you
can monitor the load level of your UPS on the “LOAD ACTIVE
METER” LEDs.
“LINE” LED:
This green light will be lit when the utility-supplied
AC line voltage at your wall outlet is nominal. It will flash if the line
voltage or frequency is outside the nominal range (either too low or
too high). No action is required on your part when the LED flashes;
the UPS continuously and automatically filters AC line power to pro-
vide your equipment with pure sine wave AC power, regardless of
brownout or overvoltage conditions. If this light is off, then AC line
voltage is not present (blackout) or is at an extremely high voltage.
Front Panel Indicator Lights
200607207 93-2525 230V Smartonline OM.qxd
11/9/2006
3:51 PM
Page 5