Uniden ANA9710 English Owners Manual
Uniden ANA9710 Manual
 |
View all Uniden ANA9710 manuals
Add to My Manuals
Save this manual to your list of manuals |
Uniden ANA9710 manual content summary:
- Uniden ANA9710 | English Owners Manual - Page 1
® ANA 9710 900 MHz Analog PBX Cordless Telephone Operating Guide - Uniden ANA9710 | English Owners Manual - Page 2
than an authorized Uniden service center for a defect or malfunction covered by this warranty, (E) used in any conjunction with equipment or parts or as part of any system not manufactured by Uniden, or (F) installed or programmed by anyone other than as detailed by the Operating Guide for this - Uniden ANA9710 | English Owners Manual - Page 3
,790 5,660,269 5,661,780 5,663,981 5,671,248 5,717,312 5,754,407 5,787,356 5,794,152 5,838,721 and other patents pending. OMANA9710 ©2001 Uniden America Corporation. All rights reserved. UCZZ01717BZ Printed in U.S.A. - Uniden ANA9710 | English Owners Manual - Page 4
any charger other than the one designed to charge this battery as specified in this Guide. Using another charger may damage the battery, or cause the battery to explode. n Do not remove or damage the battery casing. n Never throw the battery into a fire, disassemble it, or heat it. RECYCLING NICKEL - Uniden ANA9710 | English Owners Manual - Page 5
Handset Controls & Functions 1. Ringer ON/OFF switch 10. Volume (r/vol) Key 2. Message Display 11. Mute (mute) Key 3. Hold (hold) Key 12. Transfer (xfer) Key 4. Talk (talk) Key 13. Conference (conf) Key 5. Numeric Keypad 14. Flash (flash) Key 6. Pause (pause) Key 15. Channel Key 7. Redial - Uniden ANA9710 | English Owners Manual - Page 6
Base Unit Controls & Functions 18. DC Power Jack 19. Hold (hold) Key 20. Page/find (page/find) Key 21. Tone/Pulse Switch - Uniden ANA9710 | English Owners Manual - Page 7
TABLE OF CONTENTS Important Safety Instructions 2 About Your ANA 9710 4 Important Electrical Considerations 5 Range 5 Telephone Line Problems 5 Radio Interference 6 More Than One Cordless Telephone 6 Privacy 6 ANA 9710 Features 7 Installing Your ANA 9710 8 Selecting the Installation - Uniden ANA9710 | English Owners Manual - Page 8
Important Safety Instructions When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons, including the following: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked - Uniden ANA9710 | English Owners Manual - Page 9
. 13. Do not use the telephone to report a gas leak in the vicinity of the leak. CAUTION: To reduce the risk of fire or injury to persons by the battery, read and follow these instructions: 1. Use only the appropriate type and size Battery Pack specified in this Operating Guide. 2. Do not dispose of - Uniden ANA9710 | English Owners Manual - Page 10
features of your cordless phone, refer to the Handset and Base Unit illustration foldout from the front cover. Your ANA 9710 includes the following items: Base Unit Handset Telephone Cord 2 AC Adapters Rechargeable Battery (BT2499) Beltclip (EXP9702) Charging Stand Operating Guide OMANA 9710 - Uniden ANA9710 | English Owners Manual - Page 11
to such actions to allow you time for making necessary arrangements to continue uninterrupted service. If you are having trouble with your telephone service, you must first disconnect your phone to determine if it is the cause of your problem. If you determine that it is the cause, you must leave it - Uniden ANA9710 | English Owners Manual - Page 12
please check around your office to see what appliances may be causing the problem. In addition, we recommend that the Base not be plugged into a circuit . Privacy Note: Cordless phones are radio devices. Communications between the Handset and Base Unit of your cordless telephone are accomplished by - Uniden ANA9710 | English Owners Manual - Page 13
to: CONFERENCE, HOLD, and TRANSFER features n Four Function Keys: PAUSE, FLASH, REDIAL, SEARCH n 20 Number Memory Store and Search n Separate Charging Stand with Spare Battery Charging Capability n AutoStandby n AutoTalk n Vibrate Ringer Alert n Easy Installation n Out of Range Protection n Low - Uniden ANA9710 | English Owners Manual - Page 14
will use the ANA 9710 with a Standard 2500 type Telephone Desk Unit, place the ANA 9710 near that phone. Keep the Base Unit and Handset away from sources converter (making color-coded connections). Note: Your Uniden Telephone Dealer or a telephone supply store can advise you on the proper adapter or - Uniden ANA9710 | English Owners Manual - Page 15
during a lightning storm. n Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. n Use caution when installing or modifying telephone lines. You can also connect a standard 2500-type desk phone to the ANA 9710: Connect to the - Uniden ANA9710 | English Owners Manual - Page 16
Tone/Pulse Switch Be sure the TONE/PULSE switch is in the TONE position. Note: Most systems are Tone dialing. Check with your PBX Administrator if you are not sure whether your system is Tone or Pulse dialing. Applying Power to the Base and Charger Units Use only the supplied AC Adapter: EXP9704 10 - Uniden ANA9710 | English Owners Manual - Page 17
in the Charging Unit with or without the Beltclip attached. The Charging Unit also has the ability to charge a second battery with or without the Handset being charged. The Battery Packs can automatically be recharged either in or out of the Handset. Use only the supplied AC Adapter: AD-970 11 - Uniden ANA9710 | English Owners Manual - Page 18
channel of the Wall Mount stand. 4. Plug one end of the short telephone cord into the LINE jack on the Base Unit. Optionally, plug one end of a standard 2500 type desk phone into the PHONE jack. Then place the telephone cord(s) inside the molded channel(s) on the bottom of the Wall Mount stand - Uniden ANA9710 | English Owners Manual - Page 19
a wall. Before mounting your phone, consider the following: n Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. n Make sure the wall material is capable of supporting the weight of the Base - Uniden ANA9710 | English Owners Manual - Page 20
cord into the LINE jack on the Base Unit. Optionally, plug one end of a standard 2500 type desk phone into the PHONE jack. Then place the telephone cord(s) inside the molded channel(s) on the bottom of the Wall Mount stand. 4. Place the Base Unit on the posts of the wall screws and - Uniden ANA9710 | English Owners Manual - Page 21
telephone cord into a telephone wall jack. 6. Plug the AC Adapter into a standard 120V AC wall outlet by following step 7 of the Standard Wall Plate Mounting. Charging Unit Wall Mounting The Charging Unit is also designed to be wall mounted. You can mount your phone capable of supporting the weight - Uniden ANA9710 | English Owners Manual - Page 22
3. Place the Charging Unit on the posts of the wall screws and push down until it is firmly seated. 4. Plug the AC Adapter into a standard 120V AC wall outlet. 16 - Uniden ANA9710 | English Owners Manual - Page 23
Attaching the Beltclip to the Handset You can use the Beltclip to attach the Handset to your belt or pocket for convenient portability. 1. Slide the clip into the tab slot. (CAUTION: The Beltclip is designed to fit snugly onto the Handset.) 2. Press firmly until it snaps into place. on off on off - Uniden ANA9710 | English Owners Manual - Page 24
Beltclip blade and slide the clip up at the same time. on off Installing the Handset Battery Pack 1. Remove the battery cover by pressing the latch and sliding the cover down until it comes off the Handset. 2. Slide the Battery Pack down into the Handset. Note: You may have to remove the old - Uniden ANA9710 | English Owners Manual - Page 25
Pack must be fully charged before using your ANA 9710 for the first time. (Note: Charge the Battery Pack without interruption for 5 hours.) 1. Place the Handset in the front slot of the Charging Unit. 2. Make sure the CHARGE indicator lights. If the CHARGE - Uniden ANA9710 | English Owners Manual - Page 26
the display. On a Call All keys and functions are available. Handset beeps once every 3 seconds Complete your call as quickly as possible Replace Battery pack within 20 seconds to continue call. In Standby Mode None of the buttons operate. Handset beeps every 15 seconds for 3 minutes. Cannot make - Uniden ANA9710 | English Owners Manual - Page 27
and Charging Unit Contacts To maintain a good charge, it is important to clean all charging contacts on the Handset, Spare Battery Pack and Charging Unit about once a month. Use a pencil eraser or a soft dry cloth. Do not use any liquids or solvents. Using Your ANA 9710 - Uniden ANA9710 | English Owners Manual - Page 28
ANA 9710 Handset Controls Earpiece Volume Press r/vol on the side of the Handset during a call to change the earpiece volume on the handset. 22 - Uniden ANA9710 | English Owners Manual - Page 29
Handset Ringer tone and volume Press r/vol on the side of the Handset in Standby mode to select seven ringer tones and volume combinations. Vibrate Mode "Ring off" shown on the above display is the Vibrate Mode. If you set the ringer off and the Handset is not on the charger, the Handset will - Uniden ANA9710 | English Owners Manual - Page 30
Using the Handset When you pick up the Handset and press talk, you will see: After the connection has been made between the Handset and Base, you will see: Or, you may see one of the following: Condition No Connection to Base Unit Indicator Error Tone Line in Use Error Tone If the Handset is - Uniden ANA9710 | English Owners Manual - Page 31
immediately. Press talk When you finish the call, place the Handset back in the Charging Unit. AutoStandby automatically hangs up the phone. -OR- Press talk to hang up the phone Making a Call Press talk. The talk icon will illuminate after the Handset/Base are connected, and you will see: When - Uniden ANA9710 | English Owners Manual - Page 32
Feature Buttons Note: The exact operation of the Feature Buttons depends on how your PBX system is configured. Contact your PBX Administrator for more information. Placing a call "on hold" Press hold. You will hear a "beep" and see: To resume the call, press hold or talk. Transferring a Call Press - Uniden ANA9710 | English Owners Manual - Page 33
Programming the Feature Buttons The Transfer and Conference Keys can be programmed for special use, such as causing a "Hook Flash" followed by a special number or function. For example - to program the xfer key for "Hook Flash" and 9 for outside transfers only: Press mem. Press flash. Press 9. Press - Uniden ANA9710 | English Owners Manual - Page 34
" while on a call. Press once to program a "Hook Flash" in a Feature Button. REDIAL To dial the last number called, press talk, then rdl. The phone will redial the last number called. PAUSE Press once to program a Pause while storing a number in Memory. SEARCH Press to begin Memory Search. (See the - Uniden ANA9710 | English Owners Manual - Page 35
Using Your ANA 9710 Memory Use these buttons to operate the ANA 9710 Memory Storing a Number 1. Press mem. You will hear a beep, and see the message: 2. Enter the number (up to 20 digits) you want to store. a. To program a Pause in the dialing sequence, press pause. 3. Press mem. You will see the - Uniden ANA9710 | English Owners Manual - Page 36
C. Press mem. D. Press 12. The Handset beeps. This is confirmation that you have programmed 5551234 into memory location 12 and you will see: The phone then returns to Standby. Erasing a Stored Number 1. Press mem. 2. Press mem. 3. Enter the memory location number (01) to (20) you want to clear. You - Uniden ANA9710 | English Owners Manual - Page 37
and you have already established a connection between the Handset and Base Unit. 1. Press talk. 2. Press mem. 3. Enter the Memory Location (01 - 20). The phone automatically dials the number shown. Memory Search You can search all 20 Memory Locations to find the number you need. Once you have found - Uniden ANA9710 | English Owners Manual - Page 38
20). Press r/vol or mute until you reach the desired Memory Location. 4. Once you have the desired number, press talk. The talk icon appears. The phone will then automatically dial the number. Chain Dialing You can dial any stored number while you are on a call. This is sometimes needed for Long - Uniden ANA9710 | English Owners Manual - Page 39
is used in conjunction with a desk top phone to switch from the Handset to a desk top phone. 1. If you need to use a desk top phone which the ANA 9710 is connected to, press hold on the Base unit then pick up the desk top phone. 2. To resume using the Handset, press hold on the Base unit - Uniden ANA9710 | English Owners Manual - Page 40
Optional Headset (EXP9530) The optional Headset provides a "Hands-Free" Option for the ANA 9710. With the Headset installed, you can use the Beltclip to carry the Handset, and conduct a conversation using the Headset. To install the optional Headset, open the cover over the Headset Jack and plug the - Uniden ANA9710 | English Owners Manual - Page 41
to the ANA 9710. Note: A special Security Feature disconnects the Desk phone whenever the ANA 9710 Handset is in use. Connecting the Desk Telephone. Connect a telephone cord from the Desk phone to the LINE OUT jack on the ANA 9710 Base Unit. The Desk phone can now be used to answer or place calls in - Uniden ANA9710 | English Owners Manual - Page 42
for more information about your System. You can have your PBX system programmed so the following sequence occurs: 1. Your PBX telephone rings first. 2. If you don't answer the PBX telephone after a set number of rings, the call is automatically transferred to the ANA 9710. 3. If you don't answer the - Uniden ANA9710 | English Owners Manual - Page 43
Optional Accessories and Replacement Parts contact your PBX Administrator. EXP9704 AC Adapter for Base Unit Telephone Cord Beltclip EXP9702 800 mAh Battery BT-2499 Operating Guide OMANA9710 Base Unit Wall Mount EXP9660 Headset EXP9660 Charger EXP9785 AC Adapter AD970 Leather Case EXP9783 - Uniden ANA9710 | English Owners Manual - Page 44
Troubleshooting If your ANA 9710 Cordless Telephone is not performing to your expectations, please try these simple steps. If you are still unable to resolve the problems, contact your PBX Administrator. Note: Do not attempt to service this unit yourself. All service must be done by qualified - Uniden ANA9710 | English Owners Manual - Page 45
/Transmit Frequency : 902 MHz to 928 MHz Power Requirements : Nickel-Cadmium Battery Pack Size : 2 1/5 in. W x 1 2/3 in. D x 8 2/3 in. H with antenna Weight : Approx. 8.8 oz. with battery Battery : Capacity 800 mAh, 3.6 V Talk Time : 6 hours (typical) Standby Time : 4 days (typical - Uniden ANA9710 | English Owners Manual - Page 46
MEMO 40
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
 |
 |
ANA 9710
900 MHz Analog
PBX
Cordless Telephone
Operating Guide
®