Viking VBI7360W Use and Care Manual - Page 13

Caution

Get Viking VBI7360W PDF manuals and user guides View all Viking VBI7360W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Cleaning & Maintenance Condenser Cleaning Indicator The refrigerator temperature display will be blinking "CL" to indicate that it is time to clean the condenser coil. Condenser Cleaning: There is always chance of getting the condenser clogged due to dust in the air, pet hair, etc. We recommend cleaning the condenser once every 6 months. It is always better to clean the condenser coil as soon as you perform any construction activities, or work that produce lots of dusts near the unit. To clean the condenser: 1. Turn off the main power switch located at the top of unit behind the top access panel as shown in Settings and Functions - Power On/Off switch page 6. 2. Remove the bottom freezer drawer by pulling all the way out, removing the rear clips and lifting out. Details are shown in the freezer section page 10. 3. Remove the kick plate by loosening two screws and slide out though the key hole 4. Remove the access panel by removing 2 screws as shown here and pull out with force to unsnap the panel 5. Vacuum the front surface of the condenser coil using any house hold vacuum cleaner extension. It is recommended to vacuum the coil rather than using any duster. Duster may damage the fin. Make sure to remove the dust completely out of the coil area. 6. Replace the access panel and kick plate. 7. Turn main power switch on. Replace top access panel. 8. Reset and remove the "CL" from the temperature display by simultaneously pressing the up and down arrow key for 3 seconds. Glass Shelves To clean your refrigerator's glass shelves, lift the shelf out by lifting the front and releasing the hooks from the metal track. Then pull the shelf CAUTION out. Be sure to allow the glass shelves to adjust to room temperature before cleaning. Use a mild detergent with water to clean. Dry glass shelf thoroughly and replace shelf by inserting hooks into metal track and lowering front. To avoid personal injury or property damage, handle tempered glass shelves carefully. Shelves may break suddenly if nicked, scratched, or exposed to sudden temperature change. Door Gaskets Clean the door gaskets every three months using the same procedures used for interior surfaces. You should apply a light film of petroleum jelly to keep gaskets pliable. 13 Product Care

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
13
Product Care
Cleaning & Maintenance
Glass Shelves
To clean your refrigerator’s glass shelves, lift the shelf out by lifting the
front and releasing the hooks from the metal track. Then pull the shelf
out. Be sure to allow the glass shelves to adjust to room temperature
before cleaning.
Use a mild detergent with water to clean.
Dry glass
shelf thoroughly and replace shelf by inserting hooks into metal track
and lowering front.
Door Gaskets
Clean the door gaskets every three months using the same procedures used for interior surfaces. You should apply a light film of
petroleum jelly to keep gaskets pliable.
CAUTION
To avoid personal injury or property damage, handle
tempered glass shelves carefully. Shelves may break suddenly
if nicked, scratched, or exposed to sudden temperature
change.
Condenser Cleaning Indicator
The refrigerator temperature display will be blinking “CL” to indicate that it is time to clean the condenser coil.
Condenser Cleaning:
There is always chance of getting the condenser clogged due to dust in the air, pet hair, etc. We recommend cleaning the condenser
once every 6 months. It is always better to clean the condenser coil as soon as you perform any construction activities, or work that
produce lots of dusts near the unit.
To clean the condenser:
1.
Turn off
the main power switch located at the top of unit behind the top access panel as shown in Settings and Functions – Power
On/Off
switch page 6.
6.
Replace the access panel and kick plate.
7.
Turn main power switch on. Replace top access panel.
8.
Reset and remove the “CL” from the temperature display by simultaneously pressing the up and down arrow key for 3 seconds.
2.
Remove the bottom freezer drawer by pulling all
the way out, removing the rear clips and lifting
out. Details are shown in the freezer section page
10.
3.
Remove the kick plate by loosening two screws and slide out
though the key hole
4.
Remove the access panel by removing 2
screws as shown here and pull out with force
to unsnap the panel
5.
Vacuum the front surface of the condenser coil using any house hold
vacuum cleaner extension. It is recommended to vacuum the coil
rather than using any duster. Duster may damage the fin. Make sure to
remove the dust completely out of the coil area.