Vtech CL82209 User Manual - Page 11

Battery installation and charging, LOW BATTERY - phone

Get Vtech CL82209 PDF manuals and user guides View all Vtech CL82209 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Getting started Battery installation and charging Install the battery as shown on the next page. Once you have installed the battery, the screen indicates the battery status (see table below). If necessary, place the handset in the telephone base or charger to charge the battery. For best performance, keep the handset in the charger when not in use. The battery is fully charged after 16 hours of continuous charging. See the table on page 68 for battery operating times. If the screen is blank, you need to charge the handset without interruption for at least 10 minutes to give the handset enough charge to use the telephone for a short time. The screen shows LOW BATTERY and the backlight is off until you have charged the battery without interruption for at least one hour. The following table summarizes the battery charge indicators and actions to take. Battery indicators Battery status Action The screen is blank. Battery has no charge and the handset cannot be used. Charge without interruption until the screen shows LOW BATTERY (at least 10 minutes). The screen shows PLACE IN CHARGER and flashes. Battery has very little charge Charge without interruption until and the handset cannot be used. the screen shows LOW BATTERY (at least four minutes). The screen shows LOW Battery has enough charge to BATTERY and flashes. be used for a short time. Charge until the screen shows HANDSET X (about one hour). The screen shows HANDSET X. Battery is charged. To keep the battery charged, place it in the telephone base or charger when not in use. NOTE: If you are on a phone call in low battery mode, you hear four short beeps every minute. 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
Getting started
6
Battery installation and charging
Install the battery as shown on the next page. Once you have installed the
battery, the screen indicates the battery status (see table below). If
necessary, place the handset in the telephone base or charger to charge the
battery. For best performance, keep the handset in the charger when not in
use. The battery is fully charged after 16 hours of continuous charging. See
the table on page 68 for battery operating times.
If the screen is blank, you need to charge the handset without interruption
for at least 10 minutes to give the handset enough charge to use the
telephone for a short time. The screen shows
LOW BATTERY
and the
backlight is off until you have charged the battery without interruption for at
least one hour. The following table summarizes the battery charge indicators
and actions to take.
Battery indicators
Battery status
Action
The screen is blank.
Battery has no charge and the
handset cannot be used.
Charge without interruption until
the screen shows
LOW BATTERY
(at least 10 minutes).
The screen shows
PLACE
IN CHARGER
and
flashes.
Battery has very little charge
and the handset cannot be used.
Charge without interruption until
the screen shows
LOW BATTERY
(at least four minutes).
The screen shows
LOW
BATTERY
and
flashes.
Battery has enough charge to
be used for a short time.
Charge until the screen shows
HANDSET X
(about one hour).
The screen shows
HANDSET X
.
Battery is charged.
To keep the battery charged,
place it in the telephone base or
charger when not in use.
NOTE
: If you are on a phone call in low battery mode, you hear four short beeps
every minute.