Weider 8525 English Manual
Weider 8525 Manual
 |
View all Weider 8525 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider 8525 manual content summary:
- Weider 8525 | English Manual - Page 1
CUSTOMER HOT LINE: 1-800-999-3756 Mon.-Fri., 6 a.m.-6 p.m. MST CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL Visit our website at www.weiderfitness.com new products, prizes, fitness tips, and much more! - Weider 8525 | English Manual - Page 2
4 ASSEMBLY 5 ADJUSTMENTS 14 WEIGHT RESISTANCE CHART 16 TROUBLESHOOTING AND MAINTENANCE 17 CABLE DIAGRAM 18 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached to the center of this manual. Remove - Weider 8525 | English Manual - Page 3
tightened each time you use the weight system. Replace any worn parts immediately. 12. Make sure that the cables remain on the pulleys at all times. If the cables bind while you are exercising, stop immediately and make sure that the cables are on all of the pulleys. 13. Always disconnect the lat - Weider 8525 | English Manual - Page 4
your benefit, read this manual carefully before using the weight system. If you have additional questions, please call our Customer Service Department Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. ASSEMBLED DIMENSIONS: Height: 76 - Weider 8525 | English Manual - Page 5
assembly is completed. • Tighten all parts as you assemble them, unless instructed to do otherwise. • As you assemble the weight system, make sure all parts are oriented as shown in the drawings. • For help identifying small parts, use the PART IDENTIFICATION CHART at the center of this manual - Weider 8525 | English Manual - Page 6
(61), and two 5/16" Nylon Locknuts (3). Tighten the 5/16" Nylon Locknuts (3) used in step 1. Slide two Weight Bumpers (19) onto Weight Guides (62). Stack the six Weights (25) on the Weight Bumpers (19). Make sure that all of the Weights are turned so the large pin grooves are on the bottom of the - Weider 8525 | English Manual - Page 7
16" Washers (8), and two 5/16" Nylon Locknuts (3). Attach the upper ends of the Weight Guides (62) to the Top Frame (55) with a 5/16" x 6" Bolt (60) with two 5/16" x 2 1/2" Bolts (22) and two 5/16" Nylon Locknuts (3). Assemble the other Press Arm (46) in the same manner. 27 Crossbar 5 11 8 55 - Weider 8525 | English Manual - Page 8
the same manner. 70 Cable Assembly 9. During steps 9 through 20, refer to the CABLE DIAGRAM on page 18 of this manual to verify proper cable routing. Locate the Short Cable (58). Lay the Cable in the bracket on the Base (4) and under the Press Frame (17). Attach a 3 1/2" Pulley (15) to the bracket - Weider 8525 | English Manual - Page 9
3/8" Nylon Locknut (21), 3/8" Washer (9), and the 3/8" x 3 1/2" Bolt (16). 11 21 66 15 58 17 9 16 12. Route the Short Cable (58) around the 3 1/2" 12 Pulley (15). Attach the Pulley and a Cable Trap (66) to the upper hole in the Front Upright (42) with a 3/8" x 3 3/4" Bolt (71), a 3/8" Washer - Weider 8525 | English Manual - Page 10
and a 3/8" Nylon Locknut (21). Make sure that the Cable Trap is inside of the "U"-bracket. Route the Long Cable (23) between the 3 1/2" Pulley (15) and the Cable Trap (66). Make sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. 21 20 23 66 15 12 15 - Weider 8525 | English Manual - Page 11
Top Frame (55). 19 Route the Long Cable (23) around the 3 1/2" Pulley (15) and reattach it to the bracket on the Top Frame (55) with the 3/8" x 2" Bolt (12) and the 3/8" Nylon Locknut (21). Make sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. 21 55 - Weider 8525 | English Manual - Page 12
) into the ends of a 12 1/2" Pad Tube (28). Insert the Pad Tube into the Seat Frame (36). Slide two 5 1/2" Pads (30) onto the Pad Tube. Assemble the other Pad Tube (28) to the Leg Lever (29) in the same manner. 25. Rest the Seat Frame (36) on the indicated pin in - Weider 8525 | English Manual - Page 13
the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM on page 18 of this manual for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables; see TROUBLESHOOTING AND - Weider 8525 | English Manual - Page 14
ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the attachments - Weider 8525 | English Manual - Page 15
THE LOW PULLEY STATION To use the Leg Lever (29), the seat must be attached to the front upright (see ATTACHING AND REMOVING THE SEAT, on page 14). Attach the Short Cable (58) to the indicated 3/8" x 2" Eyebolt (35) with a Cable Clip (53). ATTACHING THE PREACHER PAD TO THE SEAT FRAME Set the hooks - Weider 8525 | English Manual - Page 16
the butterfly arm station is for each butterfly arm. Note: The actual resistance at each weight station may vary due to differences in individual weight plates, as well as friction between the cables, pulleys, and weight guides. WEIGHT PLATES PRESS ARM (lbs.) BUTTERFLY ARM (lbs.) LEG LEVER HIGH - Weider 8525 | English Manual - Page 17
be lifted off the weight stack. 15 57 12 66 21 2 58 23 67 2 63 Note: If a cable tends to slip off the pulleys often, the cable may have become twisted. Remove the cable and re-install it. If the cables need to be replaced, see ORDERING REPLACEMENT PARTS on the back cover of this manual. 17 - Weider 8525 | English Manual - Page 18
diagram below shows the proper routing of the Long Cable (23) and the Short Cable (58). Use the diagram to make sure that the two Cables and the cable traps have been assembled correctly. If the Cables have not been correctly routed, the weight system will not function properly and damage may occur - Weider 8525 | English Manual - Page 19
PART IDENTIFICATION CHART-Model No. WESY19512 R0903A 1/4" Nylon Locknut (2) 5/16" Nylon Locknut (3) 3/8" Nylon Jamnut (73) 1/4" Washer (10) 5/16" Washer (8) 3/8" Nylon Locknut (21) 3/8" Washer (9) 1/4" x 3/4" Screw (18) 5/16" x 1 3/4" Bolt (72) 1/4" x 2" Screw (24) 1" Retainer ( - Weider 8525 | English Manual - Page 20
5/16" x 6" Bolt (60) 3/8" x 8" Bolt (59) 2" Square Outer Cap (51) 2" Square Inner Cap (27) 1 1/2" Square Inner Cap (32) 1 3/4" Square Inner Cap (44) 1" Round Cover Cap (70) 3/4" Round Inner Cap (34) Round Inner Cap (78) 1" Round Inner Cap (49) 1 1/8" x 2 1/2" Plastic Bushing (74) 1" x 7/8" - Weider 8525 | English Manual - Page 21
Weight Tube Bumper 1" Square Inner Cap Cable Trap Small "U"-bracket 5/16" x 5" Bolt 1" Retainer 1" Round Cover Cap 3/8" x 3 3/4" Bolt 5/16" x 1 3/4" Bolt 3/8" Nylon Jamnut 1 1/8" x 2 1/2" Plastic Bushing 1" x 7/8" Plastic Bushing Top Weight Preacher Post Round Inner Cap User's Manual Exercise Guide - Weider 8525 | English Manual - Page 22
EXPLODED DRAWING-Model No. WESY19512 R0903A 68 21 20 15 66 44 11 78 8 21 21 55 3 12 27 15 7 23 50 74 6 74 48 69 70 21 69 70 - Weider 8525 | English Manual - Page 23
• The MODEL NUMBER of the product (WESY19512) • The NAME of the product (WEIDER® 8525 weight system) • The SERIAL NUMBER of the product (see the front cover of this manual) • The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST in the center of this manual) LIMITED WARRANTY ICON Health
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
 |
 |
USER'S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you
have questions, or find there are
missing or damaged parts, we
will guarantee you complete sat-
isfaction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WESY19512
Serial No.
Write the serial number in the
space above for reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
Serial Number Decal