Weider 8620 English Manual
Weider 8620 Manual
 |
View all Weider 8620 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider 8620 manual content summary:
- Weider 8620 | English Manual - Page 1
If you have questions, or if there are missing/damaged parts, we will guarantee you complete satisfaction through direct assistance from our CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. PATENT PENDING USERÕS MANUAL - Weider 8620 | English Manual - Page 2
BEFORE YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENT 16 WEIGHT RESISTANCE CHART 17 TROUBLE-SHOOTING AND MAINTENANCE 18 CABLE DIAGRAM 19 ORDERING REPLACEMENT PARTS Back Cover Note: An EXPLODED DRAWING/PART LIST and a PART IDENTIFICATION CHART are attached to the center of this manual. Remove the EXPLODED - Weider 8620 | English Manual - Page 3
arms, leg lever, lat bar, leg press plate, or nylon strap while weights are raised. The weights will fall with great force. 4. Use the home gym system only on a level surface. Cover the floor or carpet beneath the home gym system for protection. 5. Inspect and tighten all parts often. Replace - Weider 8620 | English Manual - Page 4
your benefit, read this manual carefully before Before reading further, please review the drawing using the WEIDER¨ 8620 Home Gym System. If you below and familiarize yourself with the parts that are have additional questions, please call our Customer labeled. ASSEMBLED DIMENSIONS: Height: 76 in - Weider 8620 | English Manual - Page 5
and instructions: ¥ Place all parts of the home gym system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. ¥ The assembly is divided into four stages: 1) frame assembly, 2) press and butterfly arm assembly, 3) cable and - Weider 8620 | English Manual - Page 6
yet. 42 FRAME ASSEMBLY 3 4 1 3. Press a 2Ó Square Inner Cap (27) into the open end of the Top Frame (55). Press a 1 3/4Ó Square Weight Bumpers (19) onto the bracket on the Base (4) as shown. Stack eight Weights (25) on the Weight Bumpers (19). Be sure that all of the Weights are turned so the pin - Weider 8620 | English Manual - Page 7
the holes in the Top Weight (76). Set the Top Weight onto the stack of Weights (25). Insert both Weight Guides (62) into the stack of Weights (25). Be sure that the holes in the Weight Guides are at the top, as shown. 76 Pins Holes 62 Lubricate 63 64 FRAME ASSEMBLY 25 6. Attach the upper ends - Weider 8620 | English Manual - Page 8
two 5/16Ó Nylon Locknuts (3). Assemble the other Press Arm (46) in the same manner. 9. Identify the Right Arm (48) and the Left Arm (47). Note the position of the welded bracket on each Arm. Arm identification is very important for step 10. Attach a ÒVÓ-Pulley (6) and a Long Cable Trap (50) to the - Weider 8620 | English Manual - Page 9
Press Frame (17). Hand-tighten a 5/16Ó Nylon Locknut (3) 42 onto each Carriage Bolt. Do not tighten the Nylon Locknuts until the end of this assembly Attach the Leg Lever (29) to the Rocker Arm (32) with the 3/8Ó x 2 1/2Ó Bolt and a 3/8Ó Nylon Jam Nut (33). Press a 1 3/4Ó Square Inner Cap (44) - Weider 8620 | English Manual - Page 10
15 through 29, refer to the CABLE DIAGRAM on page 19 of this manual to verify proper cable routing. Before beginning this section, identify the Long Cable (23) and the Short Cable (58) by comparing the lengths of the cables. IMPORTANT: While assembling the cables, do not overtighten the bolts and - Weider 8620 | English Manual - Page 11
CABLE ASSEMBLY 18. Route the Long Cable (23) around the ÒVÓ- 18 Pulley (6) on the Right Arm (48). Be sure that the Cable is in the groove of the ÒVÓ- Pulley and that the Long Cable Trap (50) is turned to hold the Cable for easy part identification. 23 15 Bracket 12 Route the Long Cable (23) - Weider 8620 | English Manual - Page 12
Arm (32) with a 3/8Ó x 3 1/2Ó Bolt (16), a 3/8Ó Flat Washer (9), and a 3/8Ó Nylon Locknut (21). Be sure that the Cable Trap (66) is turned to hold the Cable in place and that the Cable It is shown removed for easy part identification. Route the Short Cable (58) around the 3 1/2Ó Pulley (15) attached - Weider 8620 | English Manual - Page 13
part identification. Route the Short Cable (58) around the 3 1/2Ó Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable part identification. Route the Short Cable Cable Trap (66) is turned to hold the Cable in place and that the Cable end of the Short Cable (58) to the - Weider 8620 | English Manual - Page 14
the end of the Cable only a couple of turns, as shown in the inset drawing. Attach the Small ÒUÓ-Bracket (67) to the Weight Tube (63) with the 43 10 SEAT ASSEMBLY 31. Insert the 1/4Ó x 2 1/2Ó Carriage Bolt (38) into 31 the center hole in the Seat Plate (37). Attach the Seat Plate to the Seat - Weider 8620 | English Manual - Page 15
home gym system, pull each cable a few times to be sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM - Weider 8620 | English Manual - Page 16
Adjustment The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure that the - Weider 8620 | English Manual - Page 17
29 Weight Resistance Chart This chart shows the approximate weight resistance at each station. ÒTopÓ refers to the 6.5 lb. top weight. The other numbers refer to the 12.5 lb. weight plates. Weight resistance shown for the butterfly arm station is for each butterfly arm. WEIGHT PLATES PRESS ARM - Weider 8620 | English Manual - Page 18
Trouble-shooting and Maintenance Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable - Weider 8620 | English Manual - Page 19
below shows the proper routing of the Short Cable (58) and the Long Cable (23). Use the diagram to be sure that the two cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the home gym system will not function properly and damage may occur. The - Weider 8620 | English Manual - Page 20
1/2" x 3/4" Spacer (61) 1" Round Inner Cap (49) 1" x 7/8" Plastic Bushing (75) 3/4" Round Inner Cap (34) 1" Round Cover Cap (70) 1 3/4" Square Inner Cap (44) 2" Square Inner Cap (27) 2" Square Outer Cap (51) - Weider 8620 | English Manual - Page 21
1/4" Flat Washer (10) 5/16" Flat Washer (8) 3/8" Flat Washer (9) 5/16" x 1 3/4" Bolt (72) 5/16" x 2 1/2" Bolt (22) 5/16" x 2 3/4" Bolt (11) 1/4" x 1/2" Screw (18) 1/4" x 2 1/4" Screw (24) 5/16" x 2 1/2" Carriage Bolt (1) 5/16" x 2 3/4" Carriage Bolt (14) 1/4" x 2 1/2" Screw (43) 1/4" x 2 1/2" - Weider 8620 | English Manual - Page 22
5/16" Nylon Locknut (3) 3/8" Nylon Locknut (21) 3/8" Nylon Jam Nut (33) 1/4" Nylon Locknut (2) 3/8" x 8" Bolt (59) 3/8" x 2" Bolt (12) 3/8" x 2 1/2" Bolt (7) 3/8" x 3 1/4" Bolt (35) 3/8" x 3 1/2" Bolt (16) 3/8" x 3 3/4" Bolt (71) Cable Clip (53) 1" Retainer (69) - Weider 8620 | English Manual - Page 23
Bolt 5/16Ó x 1 3/4Ó Bolt Bumper 1 1/8Ó x 2 1/2Ó Plastic Bushing 1Ó x 7/8Ó Plastic Bushing Top Weight 3 1/2Ó Low Pulley Leg Press Plate Press Adjustment Tube Long Pad Tube UserÕs Manual Exercise Poster Note: Ò#Ó indicates a non-illustrated part. Specifications are subject to change without notice. - Weider 8620 | English Manual - Page 24
Exploded DrawingÑModel No. WESY85290 11 27 8 55 11 15 12 44 71 15 8 49 23 7 74 50 3 56 66 15 21 2 10 57 12 58 3 5 21 21 44 3 61 60 50 7 55 68 6 3 21 20 21 3 42 12 15 66 23 3 67 72 43 10 76 10 41 49 2 62 63 8 64 51 11 9 25 71 3 26 46 66 15 21 66 15 3 19 31 - Weider 8620 | English Manual - Page 25
). 2. The NAME of the product (WEIDER¨ 8620 Home Gym System). 3. The SERIAL NUMBER of the product (see the front cover of this manual). 4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING at the center of this manual). Part No. 156863 J01539-C R0699A Printed in
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
 |
 |
USER°S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to complete customer sat-
isfaction. If you have questions,
or if there are missing/damaged
parts, we will guarantee you com-
plete satisfaction through direct
assistance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.—Fri., 6 a.m.—6 p.m. MST
Visit our website at:
www.weiderfitness.com
Model No. WESY85290
Serial No.
Write the serial number in the space
above for reference.
PATENT PENDING
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number Decal