Weider Be Pro 265 Bench Enc Manual

Weider Be Pro 265 Bench Manual

Get Weider Be Pro 265 Bench PDF manuals and user guides View all Weider Be Pro 265 Bench manuals
Add to My Manuals
Save this manual to your list of manuals

Weider Be Pro 265 Bench manual content summary:

  • Weider Be Pro 265 Bench | Enc Manual - Page 1
    go to www.iconservice.ca. CUSTOMER SERVICE Call toll-free 1-888-936-4266 Mon.-Fri. 7:30 a.m.-4:30 p.m. ET (excluding holidays) or email us at [email protected] Please do not contact the store. CAUTION Read all precautions and instructions in this manual before using this equipment. Keep
  • Weider Be Pro 265 Bench | Enc Manual - Page 2
    WARNING DECAL PLACEMENT This drawing shows the location(s) of the warning decal(s). If a decal is missing or illegible, see the front cover of this manual and request a free replacement decal. Apply the decal in the location shown. Note: The decal(s) may not be shown at actual size. ATTENTION Part
  • Weider Be Pro 265 Bench | Enc Manual - Page 3
    instructions in this manual and all warnings on the weight bench before using the weight bench with pre-existing health problems. 3. The weight bench is not intended for weight bench. 12. The weight bench is designed to support a maximum user weight of 300 lbs. (136 kg), and a maximum total weight
  • Weider Be Pro 265 Bench | Enc Manual - Page 4
    4
  • Weider Be Pro 265 Bench | Enc Manual - Page 5
    for selecting the WEIDER® PRO 265 weight bench. The versatile PRO 265 weight bench is designed to model number and serial number before contacting us. The model number and the location of the serial number decal are shown on the front cover of this manual. Before reading further, please review
  • Weider Be Pro 265 Bench | Enc Manual - Page 6
    for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. Note: If a part is not in the hardware kit, check to see if it has been preassembled. Extra hardware may be included. M8 Locknut (17
  • Weider Be Pro 265 Bench | Enc Manual - Page 7
    Make sure that there is enough clearance to walk around the weight bench as you assemble it. • Place all parts in a offers Note: If you do not have internet access, call Customer Service (see the front cover of this manual) and register your product. 2. Identify the Right and Left Uprights
  • Weider Be Pro 265 Bench | Enc Manual - Page 8
    3. Attach the Crossbar (3) to the Left Upright (14) with two M10 x 77mm Carriage Bolts (18), a Support Bracket (22), and two M10 Locknuts (33); do not tighten the Locknuts yet. Attach the Crossbar (3) to the Right Upright (1) in the same way. 3 1 3 18
  • Weider Be Pro 265 Bench | Enc Manual - Page 9
    5. Attach the Frame (2) to the Front Leg (8) with three M8 x 15mm Screws (37) and three M8 5 Washers (16); do not tighten the Screws yet. 2 37 16 37 16 8 37 6. Attach the Frame (2) and the Stabilizer (13) to the Crossbar (3) with two M10 x 60mm Carriage 6 Bolts (34) and two M10 Locknuts (
  • Weider Be Pro 265 Bench | Enc Manual - Page 10
    Lever must pivot easily. 17 4 8 32 Grease 9. Apply a generous amount of the grease to the pivot rod (B) on the Frame (2) 9 Set the Backrest Support (7) into a set of brackets on the Uprights (1, 14). Orient the Backrest Tubes (5) as shown. Slide a Backrest Tube onto each side of the pivot rod
  • Weider Be Pro 265 Bench | Enc Manual - Page 11
    10. Orient the Backrest (6) so that the narrow end (C) is in the indicated location. 10 C Attach the Backrest (6) to the Backrest Tubes (5) with four M6 x 40mm Screws (30) and four M6 Washers (26); start all the Screws, and then tighten them. 6 5 26 30 26 30 11. Attach the Seat (11) to the
  • Weider Be Pro 265 Bench | Enc Manual - Page 12
    12. Attach the Curl Pad (24) to the Curl Post (27) with two M8 x 15mm Screws (37). 12 24 27 37 13. Insert the Curl Post (27) into the Front Leg (8) and align one of the adjustment holes in the Curl 13 Post with the indicated hole (D) in the Front Leg. Then, tighten the Curl Knob (31) into the
  • Weider Be Pro 265 Bench | Enc Manual - Page 13
    14. Attach a Spring Collar (25) to the weight tube on the Leg Lever (4). 14 25 4 15. Make sure that all parts are properly tightened before you use the weight bench. Extra parts may be included. The use of all remaining parts will be explained in ADJUSTMENT, beginning on page 14. 13
  • Weider Be Pro 265 Bench | Enc Manual - Page 14
    steps below explain how the weight bench can be adjusted. See the accompanying exercise guide to see the correct form for several exercises. Make sure that all parts are properly tightened each time you use the weight bench. Replace any worn parts immediately. The weight bench can be cleaned with
  • Weider Be Pro 265 Bench | Enc Manual - Page 15
    Spring Collars (25). Do not place more than 110 lbs. (49 kg), including the Barbell and Weights, on the weight rests. ATTACHING THE CURL PAD For some exercises, the Curl Pad (24) must be attached to the weight bench. Insert the Curl Post (27) into the Front Leg (8) and align an adjustment hole in
  • Weider Be Pro 265 Bench | Enc Manual - Page 16
    the flexibility of your muscles and helps to prevent post-exercise problems. Toning-Tone your muscles by working them to a moderate by completing more sets rather than by using high amounts of resistance. Weight Loss-To lose weight, use a low amount of resistance and increase the number of
  • Weider Be Pro 265 Bench | Enc Manual - Page 17
    NOTES 17
  • Weider Be Pro 265 Bench | Enc Manual - Page 18
    33 6 M10 Locknut 34 2 M10 x 60mm Carriage Bolt 35 8 Square Cap 36 2 15-pound Weight 37 6 M8 x 15mm Screw 38 2 25-pound Weight * - User's Manual * - Exercise Guide * - Grease Packet Note: Specifications are subject to change without notice. For information about ordering
  • Weider Be Pro 265 Bench | Enc Manual - Page 19
    EXPLODED DRAWING Model No. 15963C.0 R1016A 6 23 21 23 24 1 11 37 27 37 37 16 16 35 20 26 37 26 17 21 31 16 30 4 8 28 9 32 13 34 16 36 38 25 37 12 7 12 5 26 22 30 5 2 33 18 26 30 35 26 18 3 30 14 22 33 19 15 25 9 21 10 9 23 29 38 36 9 25 19
  • Weider Be Pro 265 Bench | Enc Manual - Page 20
    charge. For in-home service, the customer will be responsible for a minimal trip charge. This warranty does not extend to freight damage to the product. This warranty will automatically be voided if the product is used as a store display model, if all instructions in this manual are not followed, if
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
Model No. 15963C.0
Serial No.
Write the serial number in the space
above for reference.
CAUTION
Read all precautions and
instructions in this manual before
using this equipment. Keep this
manual for future reference.
Serial Number
Decal
(under frame)
USER’S MANUAL
To register your product and
activate your warranty today,
go to www.iconservice.ca.
Call toll-free 1-888-936-4266
Mon.–Fri. 7:30 a.m.–4:30 p.m. ET
(excluding holidays)
or email us at
Please do not contact the store.
ACTIVATE YOUR
WARRANTY
CUSTOMER SERVICE
www.weiderfitness.com