Weider Club 500 Bench English Manual - Page 7

Tighten the M10 Nylon Locknuts 32 used

Page 7 highlights

6. Press four Bushings (34) into the Backrest Frames (6) as shown. Secure the Backrest Knob (25) to the Bench Frame (2). Pull the Knob out as far as it will go. Slide the Backrest Bracket (9) between the Bench Frame tubes and engage the Knob into a hole in the Bracket. Attach the Backrest Frames (6) and two Finger Guards (14) to the Bench Frame (2) with an M10 x 146mm Bolt (36), two M10 Washers (74), and an M10 Nylon Locknut (32). Make sure that the decals are on the outside of the Finger Guards and that the Finger Guards are on the inside of the Backrest Frames. Do not overtighten the Locknut; the Bracket Frames and Pivot Guards must be able to pivot easily. 6 32 74 34 6 34 36 74 6 34 9 25 2 14 Decal 7. Press a 38mm x 50mm Inner Cap (77) into the 7 indicated end of the Seat Frame (5). Press two Bushings (34) into the Seat Frame as shown. Attach the Pivot Bracket (15) to the Seat Frame (5) with an M10 x 75mm Bolt (30) and an M10 Nylon Locknut (32). Do not overtighten the Locknut; the Pivot Bracket must be able to pivot easily. Attach the Seat (11) to the Seat Frame (5) with two M6 x 16mm Screws (31), an M6 x 53mm Bolt (29), and an M6 Washer (37). 8. Press two Bushings (34) into the Seat Frame (5) 8 as shown. Attach the Seat Frame (5) to the Backrest Frames (6) and Finger Guards (14) with an M10 x 146mm Bolt (36), two Short Spacers (61), and an M10 Nylon Locknut (32). Do not overtighten the Locknut; the Seat Frame must be able to pivot easily. Attach the Pivot Bracket (15) to the Bench Frame (2) with an M10 x 100mm Bolt (28) and an M10 Nylon Locknut (32). Do not overtighten the Locknut; the Pivot Bracket must be able to pivot easily. Tighten the M10 Nylon Locknuts (32) used in steps 1-4. 7 11 34 5 37 29 32 77 34 31 30 15 61 34 32 5 34 61 32 15 28 6 2 14 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24

31
37
32
29
30
15
7
6.
Press four Bushings (34) into the Backrest
Frames (6) as shown.
Secure the Backrest Knob (25) to the Bench
Frame (2). Pull the Knob out as far as it will go.
Slide the Backrest Bracket (9) between the Bench
Frame tubes and engage the Knob into a hole in
the Bracket.
Attach the Backrest Frames (6) and two Finger
Guards (14) to the Bench Frame (2) with an M10
x 146mm Bolt (36), two M10 Washers (74), and
an M10 Nylon Locknut (32).
Make sure that the
decals are on the outside of the Finger
Guards and that the Finger Guards are on the
inside of the Backrest Frames. Do not over-
tighten the Locknut; the Bracket Frames and
Pivot Guards must be able to pivot easily.
8.
Press two Bushings (34) into the Seat Frame (5)
as shown.
Attach the Seat Frame (5) to the Backrest
Frames (6) and Finger Guards (14) with an M10 x
146mm Bolt (36), two Short Spacers (61), and an
M10 Nylon Locknut (32).
Do not overtighten the
Locknut; the Seat Frame must be able to pivot
easily.
Attach the Pivot Bracket (15) to the Bench Frame
(2) with an M10 x 100mm Bolt (28) and an M10
Nylon Locknut (32).
Do not overtighten the
Locknut; the Pivot Bracket must be able to
pivot easily.
Tighten the M10 Nylon Locknuts (32) used in
steps 1–4.
7.
Press a 38mm x 50mm Inner Cap (77) into the
indicated end of the Seat Frame (5). Press two
Bushings (34) into the Seat Frame as shown.
Attach the Pivot Bracket (15) to the Seat Frame
(5) with an M10 x 75mm Bolt (30) and an M10
Nylon Locknut (32).
Do not overtighten the
Locknut; the Pivot Bracket must be able to
pivot easily.
Attach the Seat (11) to the Seat Frame (5) with
two M6 x 16mm Screws (31), an M6 x 53mm Bolt
(29), and an M6 Washer (37).
6
7
8
74
74
36
Decal
9
25
2
5
34
61
61
32
28
6
14
36
32
15
2
34
11
77
5
34
34
32
34
6
34
34
14
6