Weider Pro 9635 English Manual
Weider Pro 9635 Manual
 |
View all Weider Pro 9635 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider Pro 9635 manual content summary:
- Weider Pro 9635 | English Manual - Page 1
CUSTOMER HOT LINE: 1-800-999-3756 Mon.-Fri., 6 a.m.-6 p.m. MST CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL Visit our website at www.weiderfitness.com new products, prizes, fitness tips, and much more! - Weider Pro 9635 | English Manual - Page 2
3 BEFORE YOU BEGIN 4 ASSEMBLY 5 HOW TO USE THE HOME GYM SYSTEM 22 WEIGHT RESISTANCE CHART 24 TROUBLESHOOTING AND MAINTENANCE 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached - Weider Pro 9635 | English Manual - Page 3
system. 1. Read all instructions in this manual and in the accompanying literature before using the home gym system. 2. It is the responsibility of the owner to ensure that all users of the home gym system are adequately informed of all precautions. 8. Keep hands and feet away from moving parts - Weider Pro 9635 | English Manual - Page 4
using the WEIDER® PRO 9635 Home Gym System. If you have additional questions, please call our Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Lat Bar High Pulley Station VKR Arms Butterfly Arms ASSEMBLED DIMENSIONS: Height: 76 - Weider Pro 9635 | English Manual - Page 5
and instructions: • Place all parts of the PRO 9635 in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed. • The assembly is broken into five stages: 1) frame assembly, 2) press and butterfly arm assembly, 3) cable and pulley assembly - Weider Pro 9635 | English Manual - Page 6
-tighten a 5/16" Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Nylon Locknuts yet. Press a 1" Square Inner Cap (6) into the Front Upright (42). FRAME ASSEMBLY 4 1 42 6 3 6 - Weider Pro 9635 | English Manual - Page 7
55 11 49 8 44 3 44 Crossbar 3 56 42 74 FRAME ASSEMBLY 5. Slide the Rear Seat Frame (100) onto the indicated 5/16" Weight Bumpers (19) on the bracket on the Base (4) as shown. Set two Weight Bumpers (19) on the bracket on the Stabilizer (5). Stack eight Weights (25) onto each set of Weight - Weider Pro 9635 | English Manual - Page 8
(65). Set the Top Weight onto the front stack of Weights (25). Insert both Long Weight Guides (62) into the stack of Weights. Be sure that the holes in the Weight Guides are at the top, as shown. 65 Pin 63 62 Lubricate 64 Pin Grooves FRAME ASSEMBLY 25 8. Press a Weight Tube Bumper (64) into - Weider Pro 9635 | English Manual - Page 9
Weight Guides (62) to the Top Frame (55) with a 5/16" x 6" Bolt (60), two 1/2" x 3/4" Spacers (61), and a 5/16" Nylon Locknut (3). 9 61 60 73 3 61 60 3 55 62 FRAME ASSEMBLY ARM ASSEMBLY 10. Locate and open the parts bag labeled 10 "ARM ASSEMBLY Make sure that the pulleys are on the side - Weider Pro 9635 | English Manual - Page 10
two 5/16" x 2 1/2" Bolts (22) and two 5/16" Nylon Locknuts (3). 22 Assemble the other Press Arm (46) in the same manner. 46 3 17 13. Identify the yet. 13 86 31 50 Welded Brackets 31 50 47 21 Attach a "V"-Pulley (50) and a Long Cable Trap (31) to the Left Arm (47) in the same 48 manner - Weider Pro 9635 | English Manual - Page 11
84 101 83 67 56 ARM ASSEMBLY CABLE ASSEMBLY 33 101 16. Locate and open the parts bags labeled "CABLE ASSEMBLY" and "PULLEYS." 16 During steps 16 through 36, refer to the CABLE DIAGRAMS on pages 26-27 of this manual to verify proper cable routing. Before beginning this section, fully unwind - Weider Pro 9635 | English Manual - Page 12
86 50 48 CABLE ASSEMBLY 21. Attach the Pulley Bracket (20) to the Top 21 Frame (55) with the 5/16" x 5" Bolt (68) and a 68 5/16" Nylon Locknut (3). Do not overtighten the Nylon Locknut; the Pulley Bracket must be able to move freely. See the inset drawing. Route the High Cable 55 66 (58 - Weider Pro 9635 | English Manual - Page 13
sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. 22 66 21 57 23 55 58 15 12 57 Bracket 58 15 58 12 15 CABLE ASSEMBLY 21 24. Note: This assembly step shows how to complete the assembly of several pre- 24 attached parts. The 5/8" x 9/16" Spacer - Weider Pro 9635 | English Manual - Page 14
CABLE ASSEMBLY 25. Locate the Low Cable (23). Route the Low 25 Cable under the 3 1/2" Low Pulley (76) attached to the lower hole in the Press Frame (17). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame and that the Cable is between the Pulley and - Weider Pro 9635 | English Manual - Page 15
CABLE ASSEMBLY 29. Attach the end of the Low Cable (23) to the 29 Long "U"-Bracket (57) with a 1/4" Nylon Locknut (2) and a 1/4" Flat Washer (10). Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable so only a couple of threads are showing above the - Weider Pro 9635 | English Manual - Page 16
in place. 32 55 15 21 12 72 72 12 66 15 Bracket 21 5 33. Wrap the Military Press Cable (72) around a 3 1/2" Pulley (15). Attach the Pulley and a Cable Trap (66) to the Pivot Arm (101) with the 3/8" x 3 3/4" Bolt (88), a 3/8" Flat Washer (9), and a 3/8" Nylon Locknut (21). Be sure that the - Weider Pro 9635 | English Manual - Page 17
the Long "U"-Bracket. (Note: This may come pre- assembled.) Route the Military Press Cable (72) through the Long "U"-Bracket (57) and the 3 1/2" Pulley (15). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. See inset drawing B. Slide a 5/16" Flat - Weider Pro 9635 | English Manual - Page 18
CABLE ASSEMBLY 36. Attach the Press Bracket (94) to the Leg 36 Press Arm (96) with a 5/16" x 3" Bolt (75) and a 5/16" Nylon Locknut (3). Wrap the Leg Press Cable (99) around a 3 1/2" Pulley (15). Attach the Pulley to the Press Bracket (94) with the 3/8" x 2" Bolt (12) and a 3/8" Nylon Locknut ( - Weider Pro 9635 | English Manual - Page 19
SEAT ASSEMBLY 39. Attach the Front Backrest (41) to the Front 39 Upright (42) with other end of the Seat (13) to the Front Seat Frame (36) with a 1/4" Flat Washer (10) and a 1/4" x 2" Machine Screw (81). 41. Press a 1 1/2" Square Inner Cap (32) into the Leg Lever (29). 41 Lubricate the 5/16" x - Weider Pro 9635 | English Manual - Page 20
. 29 30 30 34 28 34 44. Locate and open the parts bag labeled "VKR ASSEMBLY." Press 1 1/2" Square Inner Caps (32) into the ends of 10). Attach a VKR Armrest (78) to the Right VKR Arm (80) with two 1/4" x 2" Machine Screws (81) and two 1/4" Flat Washers (10). Attach a VKR Armrest (78) to the Left - Weider Pro 9635 | English Manual - Page 21
as shown. 46 WEIDER Nameplate 42 PRO 9635 Decal 47. Make sure that all parts have been properly tightened. The use of the remaining parts will be explained in HOW TO USE THE HOME GYM SYSTEM, beginning on page 22 of this manual. Before using the home gym system, pull each cable a few times to - Weider Pro 9635 | English Manual - Page 22
HOW TO USE THE HOME GYM SYSTEM The instructions below describe how each part of the home gym system can be adjusted. Refer to the exercise poster accompanying this manual to see how the home gym system should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make - Weider Pro 9635 | English Manual - Page 23
Bolt (14) and the Seat Knob (40). For some exercises, the Seat (13) must be removed. First, be Upright (42). ATTACHING THE LEG LEVER TO THE LOW PULLEY STATION To use the Leg Lever (29), the Cable (23) with a Cable Clip (53). Attach the other end of the Chain to the 3/8" x 2" Eyebolt (35) with a Cable - Weider Pro 9635 | English Manual - Page 24
69 137 120 255 160 268 7 204 79 146 135 270 180 325 8 247 91 176 155 320 205 360 The actual resistance at each weight station may vary due to differences in individual weight plates, as well as friction between the cables, pulleys, and weight guides. 24 - Weider Pro 9635 | English Manual - Page 25
TROUBLESHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the home gym system. Replace any worn parts immediately. The home gym system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable - Weider Pro 9635 | English Manual - Page 26
the proper routing of the High Cable (58), the Low Cable (23), the Military Press Cable (72), and the Leg Press Cable (99). Use the diagrams to be sure that the four cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the home gym system will not - Weider Pro 9635 | English Manual - Page 27
Military Press Cable (72) and Leg Press Cable (99) 2 Military Press Cable (72) Rear Weight Stack-1 4 6-Pivot Arm 5 1-Long "U"-Bracket 3 2 4-Rear Seat Frame 3 Leg Press Cable (99) 27 - Weider Pro 9635 | English Manual - Page 28
17 5/16" Flat Washer (8)-8 3/8" Flat Washer (9)-7 3/8" x 1 3/4" Bolt (24)-2 1/4" x 2" Carriage Bolt (38)-1 1/4" x 2 1/2" Carriage Bolt (92)-1 1/4" x 2" Machine Screw (81)-5 5/16" x 2 1/2" Bolt (22)-4 3/8" x 2" Bolt (12)-7 5/16" x 2 1/4" Bolt (33)-3 1/4" x 2 1/2" Screw (43)-6 5/16" x 2 1/2" Carriage - Weider Pro 9635 | English Manual - Page 29
(87)-2 3/8" x 3 3/4" Bolt (88)-5 5/16" x 5" Bolt (68)-1 Cable Clip (53)-3 1" Retainer (69)-4 5/16" x 6" Bolt (60)-2 3/8" x 8" Bolt (59)-1 1 1/8" x 2 1/2" Plastic Bushing (89)-2 1" x 7/8" Plastic Bushing (90)-2 3 1/2" Pulley (15)-13 (Not shown to scale) "V"-Pulley (50)-3 (Not shown to scale) - Weider Pro 9635 | English Manual - Page 30
1/2" x 3/4" Spacer (61)-4 3/4" Round Inner Cap (34)-4 1" Square Inner Cap (6)-1 1 1/2" Square Inner Cap (32)-6 1" Round Cover Cap (70)-2 1" Round Inner Cap (49)-8 1 3/4" Square Inner Cap (44)-6 2" Square Inner Cap (27)-8 2" Square Outer Cap (51)-2 - Weider Pro 9635 | English Manual - Page 31
Rubber Bumper 1/4" x 2 1/2" Carriage Bolt 5/16" Nylon Jam Nut Press Bracket Leg Press Plate Leg Press Arm Press Pin Bushing Leg Press Cable Rear Seat Frame Pivot Arm User's Manual Exercise Poster Note: "#" indicates a non-illustrated part. Specifications are subject to change without notice. - Weider Pro 9635 | English Manual - Page 32
78 83 10 81 32 49 77 15 21 66 61 3 2 12 60 10 57 99 27 75 80 75 11 3 11 43 10 10 2 3 65 79 83 32 10 78 81 49 26 25 74 3 73 87 72 91 71 27 10 24 43 16 10 2 8 15 63 3 3 64 12 66 15 51 19 11 8 3 11 8 21 1 5 83 1 51 54 39 53 83 52 27 56 92 37 18 11 81 - Weider Pro 9635 | English Manual - Page 33
REPLACEMENT PARTS To order replacement parts, simply call our Customer Service Department toll-free WEIDER® PRO 9635 Home Gym System). 3. The SERIAL NUMBER of the product (see the front cover of this manual). 4. The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST or use, costs of removal
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
 |
 |
USER'S MANUAL
QUESTIONS?
As a manufacturer, we are com-
mitted to providing complete
customer satisfaction. If you have
questions, or find that there are
missing or damaged parts, we
will guarantee you complete sat-
isfaction through direct assis-
tance from our factory.
TO AVOID UNNECESSARY
DELAYS, PLEASE CALL DIRECT
TO OUR TOLL-FREE CUSTOMER
HOT LINE. The trained techni-
cians on our customer hot line
will provide immediate assis-
tance, free of charge to you.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WESY96352
Serial No.
Write the serial number in the space
above for reference.
Serial Number Decal (Under Seat)
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!