Weider Pro 9635 English Manual - Page 7

on the Top Frame. Press two 1 Round Inner - assembly

Page 7 highlights

4. Press a 2" Square Inner Cap (27) into the end 4 of the Top Frame (55). Press a 1 3/4" Square Inner Cap (44) into each end of the crossbar on the Top Frame. Press two 1" Round Inner Caps (49) into the top of the crossbar. 27 Attach the Top Frame (55) to the VKR Upright (74) and the Leg Press Upright (56) with two 5/16" x 2 3/4" Bolts (11) and two 5/16" Nylon Locknuts (3). Attach the Top Frame (55) to the Front 11 Upright (42) with two 5/16" x 2 3/4" Bolts (11), two 5/16" Flat Washers (8), and two 5/16" Nylon Locknuts (3). 55 11 49 8 44 3 44 Crossbar 3 56 42 74 FRAME ASSEMBLY 5. Slide the Rear Seat Frame (100) onto the indicated 5/16" x 2 1/2" Carriage Bolts (1) in the Stabilizer (5). Hand-tighten two 5/16" Nylon Locknuts (3) onto the Carriage Bolts. Attach the other end of the Rear Seat Frame (100) to the Leg Press Upright (56) with two 5/16" x 2 3/4" Bolts (11), two 5/16" Flat Washers (8), and two 5/16" Nylon Locknuts (3). Attach the Handle (82) to the Rear Seat Frame (100) with two 5/16" x 2 1/2" Carriage Bolts (1) and two 5/16" Nylon Locknuts (3). Tighten all Nylon Locknuts used in steps 1-5. 6. Set two Weight Bumpers (19) on the bracket on the Base (4) as shown. Set two Weight Bumpers (19) on the bracket on the Stabilizer (5). Stack eight Weights (25) onto each set of Weight Bumpers (19). Be sure that the pin grooves are all on the same side of each stack of Weights. Be careful not to tip either stack of Weights (25) until step 8 is complete. 5 56 8 3 6 1 100 11 3 3 1 82 5 Pin Grooves 25 25 19 5-Bracket 4-Bracket Pin Grooves 19 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33

7
4.
Press a 2” Square Inner Cap (27) into the end
of the Top Frame (55). Press a 1 3/4” Square
Inner Cap (44) into each end of the crossbar
on the Top Frame. Press two 1” Round Inner
Caps (49) into the top of the crossbar.
Attach the Top Frame (55) to the VKR Upright
(74) and the Leg Press Upright (56) with two
5/16” x 2 3/4” Bolts (11) and two 5/16” Nylon
Locknuts (3).
Attach the Top Frame (55) to the Front
Upright (42) with two 5/16” x 2 3/4” Bolts (11),
two 5/16” Flat Washers (8), and two 5/16”
Nylon Locknuts (3).
5.
Slide the Rear Seat Frame (100) onto the
indicated 5/16” x 2 1/2” Carriage Bolts (1) in
the Stabilizer (5). Hand-tighten two 5/16”
Nylon Locknuts (3) onto the Carriage Bolts.
Attach the other end of the Rear Seat Frame
(100) to the Leg Press Upright (56) with two
5/16” x 2 3/4” Bolts (11), two 5/16” Flat
Washers (8), and two 5/16” Nylon Locknuts (3).
Attach the Handle (82) to the Rear Seat
Frame (100) with two 5/16” x 2 1/2” Carriage
Bolts (1) and two 5/16” Nylon Locknuts (3).
Tighten all Nylon Locknuts used in steps
1–5.
6.
Set two Weight Bumpers (19) on the bracket
on the Base (4) as shown. Set two Weight
Bumpers (19) on the bracket on the Stabilizer
(5).
Stack eight Weights (25) onto each set of
Weight Bumpers (19).
Be sure that the pin
grooves are all on the same side of each
stack of Weights.
Be careful not to tip either stack of
Weights (25) until step 8 is complete.
4
27
55
3
3
8
49
44
44
11
11
56
42
Crossbar
5
1
1
11
82
100
5
56
8
3
3
3
25
25
19
19
5—Bracket
4—Bracket
FRAME ASSEMBLY
74
Pin
Grooves
6
Pin
Grooves