Whirlpool WDTA50SAHV Installation Guide - Page 14

POWER CORD CONNECTION, Hose clamp final position, Remove terminal box, Remove cover, Install strain

Get Whirlpool WDTA50SAHV PDF manuals and user guides View all Whirlpool WDTA50SAHV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

21. Hose clamp final position Drain hose Drain hose stop Small clamp Rubber drain hose connector Stop Stop NOTE: Route drain hose out the rear of the dishwasher. POWER CORD CONNECTION NOTE: If removing a previous dishwasher with a power cord, you will need to transfer the power cord to the new dishwasher. 22. Remove terminal box 24. Install strain relief Install a UL Listed/CSA Approved metallic strain relief. Make sure screw heads are facing up when tightening conduit nut. Strain relief is provided with the power cord kit. See the "Tools and Parts" section at the front of the guide for part details and orders. 25. Power cord - route cord into terminal box Use a 1/4" nut driver or 1/4" hex head socket wrench to remove the screw that holds the terminal box to the cross brace. Then, tilt the terminal box, free the tab, and lift the terminal box away from the crossbar. 23. Remove cover Route cord so that it does not touch dishwasher motor or lower part of dishwasher tub. Pull cord through strain relief in terminal box. NOTE: A maximum of 2 power cord supply conductors (12 AWG largest size) plus 1 grounding conductor are permitted in the terminal box. Remove the cover by sliding it up and lifting its hooks out of the slot. Retain cover for later use. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
14
NOTE:
Route drain hose out the rear of the dishwasher.
POWER CORD CONNECTION
NOTE:
If removing a previous dishwasher with a power cord,
you will need to transfer the power cord to the new dishwasher.
Use a
1
/
4
" nut driver or
1
/
4
" hex head socket wrench to remove
the screw that holds the terminal box to the cross brace. Then,
tilt the terminal box, free the tab, and lift the terminal box away
from the crossbar.
Remove the cover by sliding it up and lifting its hooks out
of the slot. Retain cover for later use.
21.
Hose clamp final position
Stop
Stop
Drain hose stop
Drain hose
Rubber drain hose
connector
Small clamp
22.
Remove terminal box
23.
Remove cover
Install a UL Listed/CSA Approved metallic strain relief.
Make sure screw heads are facing up when tightening
conduit nut. Strain relief is provided with the power cord
kit. See the “Tools and Parts” section at the front of the
guide for part details and orders.
Route cord so that it does not touch dishwasher motor or
lower part of dishwasher tub. Pull cord through strain relief
in terminal box.
NOTE:
A maximum of 2 power cord supply conductors (12 AWG
largest size) plus 1 grounding conductor are permitted in the
terminal box.
24.
Install strain relief
25.
Power cord – route cord
into terminal box