Whirlpool WRF954CIHV Owners Manual - Page 7

Energy Saver Mode and, Normal Operating Sounds, Door Alignment

Get Whirlpool WRF954CIHV PDF manuals and user guides View all Whirlpool WRF954CIHV manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Door Alignment Tools Required Depending on the width of the door opening, the following tools may be required to remove, replace, and align the refrigerator doors. Tools Needed: ■■ 1/4" hex nut driver - base grille, freezer drawer screws, and brake/leveling feet Tools Provided: ■■ 1/8" hex key - handle setscrews and door alignment Door Alignment Tool Instructions Features: ■■ Creates an even horizontal gap between the refrigerator doors. ■■ Solves door alignment issues during installation and improves door seal. Align Refrigerator Doors ✔ If doors are uneven: ■■ Ensure the refrigerator is level. ■■ Keeping both refrigerator doors closed, pull out the freezer drawer. Locate the bottom hinge pin of the right-hand refrigerator door. The alignment screw is inside the bottom hinge pin. ■■ Insert the short end of the 1/8" hex key (packed with the Door Handle Installation Instructions) into the bottom hinge pin until it is fully engaged in the alignment screw. To raise the refrigerator door, turn the hex key to the right. To lower the door, turn the hex key to the left. ■■ Continue to turn the alignment screw until the tops of the doors are aligned. Shelf Height Adjustment Shelf height can be adjusted by changing the adjustable shelf mounts between their vertical and horizontal positions. ■■ Carefully lift the shelf off the shelf mounts and turn the flipper to the desired orientation. ■■ Repeat for remaining shelf mounts. ■■ Ensure the shelf is properly seated on the shelf mounts. Energy Saver Mode and Normal Operating Sounds Your new French door bottom mount refrigerator has been designed to optimize energy efficiency and better regulate temperatures to match cooling demand. You may notice that it operates differently from your previously owned refrigerator. It is normal for the high-efficiency compressor to run for extended periods of time at varying speeds in order to consume only the energy necessary for optimum efficiency. In addition, during various stages of the cooling cycle, you may hear normal operating sounds that are unfamiliar to you. Energy Saver Mode A selectable feature that turns off the heaters around the refrigerator doors and dispenser. When this feature is enabled, condensation may form on the front of the refrigerator cabinet, gasket, or on top of the freezer drawer. Savings may vary based on the relative humidity of the environment. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
7
Shelf Height Adjustment
Shelf height can be adjusted by changing the adjustable shelf
mounts between their vertical and horizontal positions.
■
Carefully lift the shelf off the shelf mounts and turn the flipper
to the desired orientation.
■
Repeat for remaining shelf mounts.
■
Ensure the shelf is properly seated on the shelf mounts.
Energy Saver Mode and
Normal Operating Sounds
Your new French door bottom mount refrigerator has been
designed to optimize energy efficiency and better regulate
temperatures to match cooling demand.
You may notice that it operates differently from your previously
owned refrigerator.
It is normal for the high-efficiency compressor to run for extended
periods of time at varying speeds in order to consume only the
energy necessary for optimum efficiency.
In addition, during various stages of the cooling cycle, you may
hear normal operating sounds that are unfamiliar to you.
Energy Saver Mode
A selectable feature that turns off the heaters around the
refrigerator doors and dispenser. When this feature is enabled,
condensation may form on the front of the refrigerator cabinet,
gasket, or on top of the freezer drawer. Savings may vary based
on the relative humidity of the environment.
Door Alignment
Tools Required
Depending on the width of the door opening, the following tools
may be required to remove, replace, and align the refrigerator
doors.
Tools Needed:
■
1/4" hex nut driver – base grille, freezer drawer screws, and
brake/leveling feet
Tools Provided:
■
1/8" hex key – handle setscrews and door alignment
Door Alignment Tool Instructions
Features:
■
Creates an even horizontal gap
between the refrigerator doors.
■
Solves door alignment issues during
installation and improves door seal.
Align Refrigerator Doors
✔
If doors are uneven:
■
Ensure the refrigerator is level.
■
Keeping both refrigerator doors closed, pull out the freezer
drawer. Locate the bottom hinge pin of the right-hand
refrigerator door. The alignment screw is inside the bottom
hinge pin.
■
Insert the short end of the 1/8" hex key (packed with the
Door Handle Installation Instructions) into the bottom hinge
pin until it is fully engaged in the alignment screw.
To raise the refrigerator door, turn the hex key to the right.
To lower the door, turn the hex key to the left.
■
Continue to turn the alignment screw until the tops of the
doors are aligned.